The MCR 60n is a streaming integrated amplifier by Marantz that delivers 65 watts x 2 channels into 4 ohms, or 33 watts x 4 channels into 4 ohms when both speaker pairs are driven. Marantz publishes no 8 ohm or 6 ohm figure. Bi-amping and parallel bridge-tied load are both supported, and the rear panel is marked for 4 to 16 ohm loads.. It was released in September 2026. It is a 2-channel design. Bridged to mono it delivers Parallel BTL, and bi-amping, which is the usual way to use a pair of these on a demanding speaker. Speakers connect via binding posts. A minimum impedance of 4 ohms makes it compatible with a wide range of loudspeakers. It has a built-in DAC, so you can play digital sources directly with no separate DAC unit needed. It also has a phono input, so a turntable can connect straight to it. The Marantz MCR 60n has an MSRP of $1,000.
Marantz replaced the older Marantz M-CR612 with this model. Follow the link to read our detailed comparison of these models:
Compare Marantz MCR 60n vs Marantz M-CR612
There are 10 Marantz amplifiers in our database. Below you can see the main specs of these amps.
Marantz Integrated Amplifier Series
Performance Specs
One of the most important factors when deciding on an integrated amplifier is its power ratings and compatibility with your speaker's impedance requirements. The Marantz MCR 60n is rated at 65 watts RMS into 4-ohms. Marantz provides this wattage at a THD (Total Harmonic Distortion) of 0.1% at 1 kHz, 5 W, 4 ohms which is an important indicator of distortion at the given values (lower THD is better).
Here are the main highlights of its performance specs:
- 65 watts into 4-ohms
- 4-ohms Min Impedance (allows compatibility with a wide range of loudspeakers)
- 90dB Signal to Noise Ratio
Built-in Sources
Most integrated amplifiers expect you to bring your own source. Marantz MCR 60n does not:
- CD player built in - one of only 6 amplifiers in our database with a disc drawer. One box instead of two, and no interconnect between them.
- AM/FM radio built in.
Wiring more than one pair of speakers to it? Check the load first →
When pairing the Marantz MCR 60n with a passive Bookshelf (Stand mount) or Passive Floor Standing (Tower) speaker, you have to check if their Max Power Range is below the max wattage of the amp for the given impedance levels.
Operating your amp outside of this max range may damage the speakers.
Inputs and Outputs
Besides the performance specs of the Marantz MCR 60n, the next important feature set that you have to evaluate is the input and output selections that it offers.
Marantz MCR 60n has total of 1 Analog inputs .
Inputs
- Total Number of Analog Inputs: 1
- Phono Input
- 1 Optical Digital Input
- USB Input:
- HDMI Input (eARC)
Outputs
- Speaker Outputs (A/B switchable)
- Main pre-out (AUX assignable), Sub Preamp Outputs
- Yes Headphone Output
- Subwoofer Output (1)
Bluetooth Connectivity
Marantz MCR 60n features built-in Bluetooth for wireless music streaming from your Bluetooth-enabled devices such as Apple iPod/iPhone/iPad, Android smartphone/tablet, Windows PC, Mac computers/laptops.
Among the amps in the same price range, these are the 5 amps that have Bluetooth Connectivity:
Bluetooth Transmitter:Marantz MCR 60n can also act as a Bluetooth transmitter, making it possible to stream the music from the amp to your bluetooth headphones or speakers.
Phono Input
Marantz MCR 60n features two Phono Inputs which are compatible with
MM (Moving Magnet) type of phono cartridges, you can connect your turntable with MM cartridges directly to this amp without the need for a phono preamp. If you are using an MC cartridge on your turntable, you need to use a phono preamp that has MC phono stage such as the
Cambridge Duo or the
iFi ZEN Phono.
Subwoofer Output
Marantz MCR 60n has a dedicated subwoofer output which can be used to connect it directly to a powered subwoofer via an LFE(Low Frequency Effects) cable.
Check our
Powered Subwoofers page to find a subwoofer that will work with Marantz MCR 60n amp and your speakers.
DAC and Digital Music
The Marantz MCR 60n's built-in DAC allows the connection of digital sources directly, eliminating the need for an external DAC.
Marantz MCR 60n Pros and Cons
Drawn from the published figures on this page, not from listening.
- ✓Built-in DAC handling 32-bit-bit / 384 kHz and DSD, so a TV, computer or streamer can connect digitally with nothing in between.
- ✓Digital inputs cover 1 optical and USB.
- ✓Phono stage built in (MM), so a turntable needs no separate preamplifier.
- ✓Streams over the network without a separate streamer: Spotify Connect, Tidal, Amazon Music, TuneIn and Pandora; AirPlay 2, Roon and HEOS.
- ✓Bluetooth for playing straight from a phone.
- ✓Pre-outs (Main pre-out (AUX assignable), Sub) leave room to add a power amplifier or an active subwoofer later.
- ✓A and B speaker terminals, for a second pair or for bi-wiring.
- ✓Headphone output.
- ✓Has tone controls.
- ✓At 279mm wide it fits where a full-size component will not.
- ✓Built-in AM/FM tuner.
- ✓CD player built in.
- ✓App control (HEOS).
- ✗Only 1 analogue input, so a second source means unplugging the first.
- ✗The phono stage is moving-magnet only; a moving-coil cartridge would need a step-up or an external stage.
Marantz MCR 60n External Dimensions and Weight
Marantz MCR 60n has external dimensions of (H x W x D) 4-3/8 x 11 x 11-7/8 inch (111.8 x 279.4 x 302.3 mm ). The unit weighs
4.2 kg (9.3 lbs).
Base Surface Area
Base surface area of an integrated amplifier may become an important decision factor when the space in your room or desk is limited.
The base area of the Marantz MCR 60n is approximately 844.6cm2 / 130.9inch2.
- Width: 279.4mm (11")
- Height: 111.8mm (4-3/8")
- Depth: 302.3mm (11-7/8")
- Weight: 4.2 kg (9.3 lbs)
- Base Surface Area: ~844.6cm2 / 130.9inch2
- Volume: ~9.4 liter / 2.5 gallon
Available colors
Marantz MCR 60n is available in Black color options.
What's in the Box of Marantz MCR 60n?
Here are the items that are included inside the box of MCR 60n:
- Main unit
- AC cord
- Remote control
- Batteries
- FM antenna
- AM antenna
- Quick start guide
Official Product Page
Official manufacturer's product page for the Marantz MCR 60n Integrated Amplifier can be found below:
Official Product Page for Marantz MCR 60n
| General |
| Brand |
Marantz |
| Full Model Name |
Marantz MCR 60n |
| Release Date |
September 2026 |
| Amplifier Type |
Integrated Amplifier |
| Number of Channels |
2 |
| Amplifier Technology |
Solid State |
| Performance |
| Watts RMS per Channel into 8-ohms |
N/A |
| Watts RMS per Channel into 6-ohms |
N/A |
| Watts RMS per Channel into 4-ohms |
65 watts |
| Bridged Power per Channel |
Parallel BTL, and bi-amping |
| Frequency Bandwidth |
10 Hz-40 kHz |
| THD |
0.1% at 1 kHz, 5 W, 4 ohms |
| Minimum Impedance |
4 |
| Signal to Noise Ratio |
90 dB |
| Signal to Noise Ratio (MM) |
74 |
| Digital Music |
| Built-in DAC |
Yes |
| Bluetooth |
Yes |
| WiFi |
Yes |
| Ecosystem |
| Apple AirPlay |
|
| Apple AirPlay2 |
Yes |
| DTS Play-Fi |
|
| Chromecast built-in |
|
| Roon |
Ready |
| HEOS |
Yes |
| BluOS |
|
| CONNECTIONS |
| Total Analog Inputs |
1 |
| Phono Input |
Yes |
| Optical Digital Inputs |
1 |
| Coaxial Digital Inputs |
No |
| USB Input |
Yes |
| USB Type |
USB A |
| Preamp Outputs |
Main pre-out (AUX assignable), Sub |
| Headphone Output |
Yes |
| Subwoofer Output |
Yes |
| Removable Power Cord |
|
| Speaker Connectors |
Binding posts |
| Speaker Outputs |
A / B, with individual volume |
| PHYSICAL SPECS |
| Height |
111.8mm (4-3/8") |
| Width |
279.4mm (11") |
| Depth |
302.3mm (11-7/8") |
| Weight |
4.2 kg (9.3 lbs) |
| Available Colors |
Black |
| OTHER |
| Tone Controls |
Yes |
| Parts Warranty |
|
| Labor Warranty |
|