In this review, we will be comparing R5 Meta and R11 Meta, two Passive Floor-standing speakers by KEF Let's have a brief look at the main features
of KEF R5 Meta and KEF R11 Meta first before getting into our more
detailed comparison.
R5 Meta and R11 Meta are members of KEF's R META series of speakers. Below you can find the loudspeakers from this series.
What size room are the KEF R5 Meta and KEF R11 Meta speakers good for?
The size of the room in which you are planning to use these loudspeakers is an important decision factor. Here we have compared their suitability to various sizes of environments considering their size and max power parameters:
In the following sections, we will get into more detail in order to better understand how the KEF R5 Meta and KEF R11 Meta compare and hopefully end up with enough arguments to decide which one of these loudspeakers is the better choice for you.
**This post contains affiliate links, and I will be compensated if you make a purchase after clicking
through my links. As an Amazon Associate I earn from qualifying purchases.
Drivers
Both R5 Meta and R11 Meta are 3-way speakers.
| Driver |
KEF R5 Meta |
KEF R11 Meta |
|
Driver Setup
|
3-way
|
3-way
|
|
Tweeter
|
1-inch
|
1-inch
|
|
Midrange
|
1 x 5-inch |
1 x 5-inch |
|
Woofer
|
2 x 5.25-inch
|
4 x 6.5-inch
|
R5 Meta features a 1" Aluminum with MAT absorber Vented dome Tweeter , a 5" Midrange and 2 x 5.25" Hybrid Aluminum Woofer with a Crossover frequency at 400Hz and 2700Hz. On the other hand, the R11 Meta features a 1" Aluminum with MAT absorber Vented dome Tweeter , a 5" Midrange and 4 x 6.5" Hybrid Aluminum Woofer with a Crossover frequency at 330Hz and 2500Hz.
Frequency Response
R5 Meta has a frequency range of 52-28k Hz whereas R11 Meta has a frequency range of 46-28 Hz. With a minimum frequency of 46Hz, the R11 Meta can go significantly deeper on the low side and provide stronger bass compared to the R5 Meta's min frequency of 52Hz.
Below graphs depict how these two speakers compare with the max, min and average values of the Min and Max Frequencies of other speakers in the Floor-standing class in our database.
Low Frequency
Floor-standing Speakers
High Frequency
Floor-standing Speakers
None of these speakers achieves full range experience which is commonly agreed as 20Hz-20kHz. In order to achieve lower lows / deeper bass, we recommend you pair these with a subwoofer. Visit our Powered Subwoofers section to find out more about the available options.
Impedance and Sensitivity
R5 Meta and R11 Meta have the same Impedance of 4 ohms but where they differ is the sensitivity levels. R5 Meta sensitivity is rated at 87 dB and the R11 Meta's is at 90 dB. This 3 dB difference makes the KEF R11 Meta a more sensitive speaker compared to KEF R5 Meta, hence will play louder with the same amount of watts.
One thing to keep in mind that the lower impedance speakers, especially the ones that are rated at 4 ohms may put more pressure on the amplifier unit comared to higher impedance speakers especially at high volume levels, so make sure the amp you pair with the R5 Meta and the R5 Meta can provide this impedance level.
Sensitivity
Floor-standing Speakers
Power Range
Power
range is the range of input power in watts RMS that a loudspeaker is designed to handle. While using an amplifier within this range ensures the nominal performance , inputting a power that is higher than the max wattage can result in a damaged speaker.
R5 Meta can handle a max power of 300 watts RMS from the amp the whereas R5 Meta has a max power handling value of 200 watts RMS , 100 watts less than the R11 Meta.
Keep in mind that a higher max power handling value doesn't necessarily make that a louder speaker
compared to a lower max handling speaker. Loudness or the sound level is also impacted by parameters
such as Impedance, sensitivity and system efficiencies.
Input Type and Bi-Amping / Bi-Wiring
Both R5 Meta and R11 Meta features dual binding post speaker terminals for bi-amping or bi-wiring.
KEF R5 Meta's Custom 5-way bi-wire tool-less binding posts terminals allows Bi-amping or bi-wiring
KEF R11 Meta's Custom 5-way bi-wire tool-less binding posts terminals allows Bi-amping or bi-wiring
Cabinet Type and Port Position
Both R5 Meta and R11 Meta have rear firing ports. Rear ported speakers generally need more room between the backside of the speaker and the wall compared to sealed and front/bottom ported speakers. Placing the speakers too close to the walls may cause the bass to sound boomy.
If you are limited in space and can't get the speakers away from the backwall, check our Speakers with Front Firing Ports page.
KEF R11 Meta Port
Physical Specs
Size of a speaker can sometimes become an important decision factor due to space constraints or in some cases purely for esthetic reasons. In this section, we are going to compare KEF R5 Meta's and KEF R11 Meta's external dimensions. KEF R5 Meta has external dimensions of 1074.0 x 274.0 x 343.0mm ( 42-1/4-inch x 10-3/4-inch x 13-1/2-inch) whereas KEF R11 Meta has external dimensions of 1296.0 x 312.0 x 385.0mm ( 51-inch x 12-1/4-inch x 15-1/8-inch) .
KEF R11 Meta is clearly the larger of the two speakers. Its body is 38mm wider, 222mm taller and 42mm deeper than KEF R5 Meta.
Below you can see the front view size comparison of KEF R5 Meta and KEF R11 Meta in scale.
Comparison image of KEF R5 Meta and KEF R11 Meta Size and External Dimensions
Base Surface Area Comparison
Base surface area of a loudspeaker may become a determining factor when the space in your room or desk is limited.
The base surface area of the KEF R5 Meta is approximately 939.8cm2 / 145.7inch2 and base area of the KEF R11 Meta is approximately 1201.2cm2 / 186.2inch2. The R5 Meta requires 22% less surface area than the R11 Meta which gives it a small advantage on placement in tight spaces.
Weight Comparison The weight of a loudspeaker can become an important factor if you need to move and reposition the unit often. Weight of a speaker can also "sometimes" be an indicator of the rigidity of the enclosure and the quality of the internal components used. The KEF R5 Meta weighs 24.55kg / 54lbs and the KEF R11 Meta weighs 36.59kg / 80.5lbs. This makes the R11 Meta 49% heavier than the R5 Meta.
Here is a comparison of how R5 Meta and R11 Meta's weights compare with the average, max and min weights in Passive Floor-standing class.
Weight
All Floor-standing Speakers
What's in the Box of KEF R5 Meta?
Here are the items that are included inside the box of R5 Meta:
R5 Meta Microfiber grille Plinth and spike accessories Port bungs User manual and warranty information
What's in the Box of KEF R11 Meta?
Here are the items that come with the R11 Meta:
R11 Meta Microfiber grille Plinth and spike accessories Port bungs User manual and warranty information
 Height |
1074mm
vs
1296mm
|
Easier to fit in smaller spaces |
 Base Surface Area |
939cm2 (274x343mm)
vs
1201cm2 (312x385mm)
|
Takes less floor space |
 Price per pair* |
3998USD
vs
6498USD
|
costs less (*prices may change depending on the seller, location and time) |
 Max Input Power |
300 watts
vs
200 watts
|
Handle more power from your amplifier |
 Sensitivity |
90 dB
vs
87 dB
|
Play louder with same amount of amplification power |
 Woofer Size |
6.5 inches
vs
5.25 inches
|
Larger woofer |
| Number of Woofers |
4
vs
2
|
More woofers |
| Low Frequency Response |
46 Hz
vs
52 Hz
|
Generates deeper bass |
| General |
KEF R5 Meta |
KEF R11 Meta |
| Brand |
KEF |
KEF |
| Speaker Type |
Floor-standing speaker |
Floor-standing speaker |
| Power Range |
15-200 watts |
15-300 watts |
| Sensitivity |
87 dB |
90 dB |
| Impedance |
4 ohms |
4 ohms |
| Impedance |
3.2 ohms |
3.2 ohms |
| Frequency Response |
52-28k Hz |
46-28 Hz |
Drivers |
|
|
| Woofer Quantity |
2 |
4 |
| Woofer Size |
5.25" |
6.5" |
| Woofer Composition |
Hybrid Aluminum |
Hybrid Aluminum |
| Woofer Surround Material |
Rubber |
Rubber |
| Tweeter Size |
1" |
1" |
| Tweeter Type |
Vented dome |
Vented dome |
| Aimable Tweeter |
No |
No |
| Midrange Driver |
5" |
5" |
| Crossover Frequency |
400Hz and 2700Hz |
330Hz and 2500Hz |
| Firing Direction |
rear |
rear |
Physical Specs |
|
|
| Height |
1074.0mm (42.3") |
1296.0mm (51") |
| Width |
274.0mm (10.8") |
312.0mm (12.3") |
| Depth |
343.0mm (13.5") |
385.0mm (15.2") |
| Weight |
24.55kg (54lbs) |
36.59kg (80.5lbs) |
| Enclosure |
Bass Reflex |
Bass Reflex |
| Available Colors |
Black Gloss, White Gloss, Walnut |
Black Gloss, White Gloss, Walnut |
| Moisture Resistancy |
No |
No |
Connections |
|
|
| Biamp Inputs |
Yes |
Yes |
Other |
|
|
| Parts Warranty |
5 years |
5 years |
| Labor Warranty |
5 years |
5 years |