In this review, we will be comparing SS-CS3 and TSi400, two Passive Floor-standing speakers from Sony and Polk Audio. Let's have a brief look at the main features
of Sony SS-CS3 and Polk TSi400 first before getting into our more
detailed comparison.
What size room are the Sony SS-CS3 and Polk TSi400 speakers good for?
The size of the room in which you are planning to use these loudspeakers is an important decision factor. Here we have compared their suitability to various sizes of environments considering their size and max power parameters:
In the following sections, we will get into more detail in order to better understand how the Sony SS-CS3 and Polk TSi400 compare and hopefully end up with enough arguments to decide which one of these loudspeakers is the better choice for you.
**This post contains affiliate links, and I will be compensated if you make a purchase after clicking
through my links. As an Amazon Associate I earn from qualifying purchases.
Drivers
One of the fundamental differences between these two speakers is that SS-CS3 is a 3-way design whereas the TSi400 is a 2-way speaker. 3-way designs utilize a midrange driver in addition to the tweeter and woofer on 2-way designs. Designing a crossover for a 3-way speaker is a complicated process and generally increases the overall cost of the speaker.
| Driver |
Sony SS-CS3 |
Polk TSi400 |
|
Driver Setup
|
3-way
|
2-way
|
|
Super Tweeter
|
0.75-inch |
- |
|
Tweeter
|
1-inch
|
1-inch
|
|
Midrange
|
- |
- |
|
Woofer
|
2 x 5.12-inch
|
3 x 5.25-inch
|
SS-CS3 features a 1" polyester fiber Soft-Dome Tweeter , a 0.75" Supertweeter and 2 x 5.12" Mica Reinforced Cellular (MRC) Woofer . On the other hand, the TSi400 features a 1" Tweeter and 3 x 5.25" Organic Fiber Woofer .
Frequency Response
SS-CS3 has a frequency range of 45-50k Hz whereas TSi400 has a frequency range of 44-24k Hz. With a minimum frequency of 44Hz, the TSi400 can go slightly deeper then the SS-CS3's min frequency of 45Hz.
Below graphs depict how these two speakers compare with the max, min and average values of the Min and Max Frequencies of other speakers in the Floor-standing class in our database.
Low Frequency
Floor-standing Speakers
High Frequency
Floor-standing Speakers
None of these speakers achieves full range experience which is commonly agreed as 20Hz-20kHz. In order to achieve lower lows / deeper bass, we recommend you pair these with a subwoofer. Visit our Powered Subwoofers section to find out more about the available options.
Impedance and Sensitivity
SS-CS3 is a 6 ohms speaker compared to the TSi400 which has a nominal impedance of 8 ohms.
These two speakers also have different sensitivity levels. SS-CS3 sensitivity is rated at 88 dB and the TSi400's is rated at 91 dB. This 3 dB difference makes the Polk TSi400 a more sensitive speaker compared to Sony SS-CS3, hence will play louder with the same amount of watts.
Sensitivity
Floor-standing Speakers
Power Range
Power
range is the range of input power in watts RMS that a loudspeaker is designed to handle. While using an amplifier within this range ensures the nominal performance , inputting a power that is higher than the max wattage can result in a damaged speaker.
SS-CS3 can handle a max power of 200 watts RMS from the amp the whereas SS-CS3 has a max power handling value of 145 watts RMS , 55 watts less than the TSi400.
Keep in mind that a higher max power handling value doesn't necessarily make that a louder speaker
compared to a lower max handling speaker. Loudness or the sound level is also impacted by parameters
such as Impedance, sensitivity and system efficiencies.
Input Type and Bi-Amping / Bi-Wiring
TSi400 features 5-way post posts which make bi-amping or bi-wiring possible. SS-CS3 has a Post which doesn't feature bi-amping/bi-wiring.
Cabinet Type and Port Position
SS-CS3 has a rear firing port whereas TSi400 has a bottom firing ports. Polk TSi400's bottom-firing port gives more flexibility in placement in regards to proximity to walls compared to Sony SS-CS3 with its rear-firing port.
Physical Specs
Size of a speaker can sometimes become an important decision factor due to space constraints or in some cases purely for esthetic reasons. In this section, we are going to compare Sony SS-CS3's and Polk TSi400's external dimensions. Sony SS-CS3 has external dimensions of 922.0 x 230.0 x 260.0mm ( 36.30 x 9.05 x 10.24inch) whereas Polk TSi400 has external dimensions of 985.0 x 208.0 x 369.0mm ( 38-3/4 x 8-3/16 x 14-1/2inch) .
Sony SS-CS3 is 63mm shorter and 109mm less deeper than Polk TSi400 but it is also 22mm wider.
Base Surface Area Comparison
Base surface area of a loudspeaker may become a determining factor when the space in your room or desk is limited.
The base surface area of the Sony SS-CS3 is approximately 598.0cm2 / 92.7inch2 and base area of the Polk TSi400 is approximately 767.5cm2 / 119.0inch2. The SS-CS3 requires 22% less surface area than the TSi400 which gives it a small advantage on placement in tight spaces.
Weight Comparison The weight of a loudspeaker can become an important factor if you need to move and reposition the unit often. Weight of a speaker can also "sometimes" be an indicator of the rigidity of the enclosure and the quality of the internal components used. The Sony SS-CS3 weighs 10.60kg / 23.3lbs and the Polk TSi400 weighs 14.55kg / 32lbs. This makes the TSi400 37% heavier than the SS-CS3.
Here is a comparison of how SS-CS3 and TSi400's weights compare with the average, max and min weights in Passive Floor-standing class.
Weight
All Floor-standing Speakers
What's in the Box of Polk TSi400?
Here are the items that come with the TSi400:
Tower speakerDetachable cloth grille (installed)Owners ManualWall-Mount templateOnline registration sheetPolk Audio product brochure
 Driver Setup |
3-way
vs
2-way
|
Have a dedicated mid-range driver |
 High Frequency Response |
50k Hz
vs
24k Hz
|
Generates higher frequency |
 Height |
922mm
vs
985mm
|
Easier to fit in smaller spaces |
 Base Surface Area |
598cm2 (230x260mm)
vs
767cm2 (208x369mm)
|
Takes less floor space |
 Price per pair* |
358USD
vs
498USD
|
costs less (*prices may change depending on the seller, location and time) |
 Max Input Power |
200 watts
vs
145 watts
|
Handle more power from your amplifier |
 Sensitivity |
91 dB
vs
88 dB
|
Play louder with same amount of amplification power |
 Nominal Impedance |
8 ohms
vs
6 ohms
|
Less selective with amplifiers |
 Woofer Size |
5.25 inches
vs
5.12 inches
|
Larger woofer |
| Number of Woofers |
3
vs
2
|
More woofers |
| Low Frequency Response |
44 Hz
vs
45 Hz
|
Generates deeper bass |
 Bi-Amping and Bi-Wiring |
Yes
vs
No
|
Allows bi-amping and bi-wiring connections |
| General |
Sony SS-CS3 |
Polk Audio TSi400 |
| Brand |
Sony |
Polk Audio |
| Speaker Type |
Floor-standing speakers |
Floor-standing speaker |
| Power Range |
up to 145 watts |
20-200 watts |
| Sensitivity |
88 dB |
91 dB |
| Impedance |
6 ohms |
8 ohms |
| Frequency Response |
45-50k Hz |
44-24k Hz |
Drivers |
|
|
| Woofer Quantity |
2 |
3 |
| Woofer Size |
5.12" |
5.25" |
| Woofer Composition |
Mica Reinforced Cellular (MRC) |
Organic Fiber |
| Woofer Surround Material |
Rubber |
Butyl Rubber |
| Tweeter Size |
1" |
1" |
| Tweeter Type |
Soft-Dome |
n/a |
| Aimable Tweeter |
No |
No |
| Midrange Driver |
No |
No |
| Firing Direction |
rear |
bottom |
Physical Specs |
|
|
| Height |
922.0mm (36.3") |
985.0mm (38.8") |
| Width |
230.0mm (9.1") |
208.0mm (8.2") |
| Depth |
260.0mm (10.2") |
369.0mm (14.5") |
| Weight |
10.60kg (23.3lbs) |
14.55kg (32lbs) |
| Enclosure |
Bass Reflex |
Bass Reflex |
| Finish |
MDF/Wood-veneer |
Wood-grain vinyl |
| Available Colors |
Black |
Cherry |
| Grille |
Yes |
Yes |
| Moisture Resistancy |
No |
No |
Connections |
|
|
| Biamp Inputs |
No |
Yes |
Other |
|
|
| Parts Warranty |
2 years |
5 Years |
| Labor Warranty |
2 years |
5 Years |