In this review, we will be comparing SE 6000F and RP-6000F, two Passive Floor-standing speakers from Paradigm and Klipsch. Let's have a brief look at the main features
of Paradigm SE 6000F and Klipsch RP-6000F first before getting into our more
detailed comparison.
What size room are the Paradigm SE 6000F and Klipsch RP-6000F speakers good for?
The size of the room in which you are planning to use these loudspeakers is an important decision factor. Here we have compared their suitability to various sizes of environments considering their size and max power parameters:
In the following sections, we will get into more detail in order to better understand how the Paradigm SE 6000F and Klipsch RP-6000F compare and hopefully end up with enough arguments to decide which one of these loudspeakers is the better choice for you.
**This post contains affiliate links, and I will be compensated if you make a purchase after clicking
through my links. As an Amazon Associate I earn from qualifying purchases.
Drivers
One of the fundamental differences between these two speakers is that SE 6000F is a 3-way design whereas the RP-6000F is a 2-way speaker. 3-way designs utilize a midrange driver in addition to the tweeter and woofer on 2-way designs. Designing a crossover for a 3-way speaker is a complicated process and generally increases the overall cost of the speaker.
| Driver |
Paradigm SE 6000F |
Klipsch RP-6000F |
|
Driver Setup
|
3-way
|
2-way
|
|
Tweeter
|
1-inch
|
1-inch
|
|
Midrange
|
1 x 5.5-inch |
- |
|
Woofer
|
3 x 5.5-inch
|
2 x 6.5-inch
|
SE 6000F features a 1" Tweeter , a 5.5" Midrange and 3 x 5.5" Mineral-filled polypropylene Woofer . On the other hand, the RP-6000F features a 1" Tractrix Horn Tweeter and 2 x 6.5" Cerametallic Woofer .
Frequency Response
SE 6000F has a frequency range of 53-21k Hz whereas RP-6000F has a frequency range of 34-25k Hz. With a minimum frequency of 34Hz, the RP-6000F can go significantly deeper on the low side and provide stronger bass compared to the SE 6000F's min frequency of 53Hz.
Below graphs depict how these two speakers compare with the max, min and average values of the Min and Max Frequencies of other speakers in the Floor-standing class in our database.
Low Frequency
Floor-standing Speakers
High Frequency
Floor-standing Speakers
None of these speakers achieves full range experience which is commonly agreed as 20Hz-20kHz. In order to achieve lower lows / deeper bass, we recommend you pair these with a subwoofer. Visit our Powered Subwoofers section to find out more about the available options.
Impedance and Sensitivity
SE 6000F and RP-6000F have the same Impedance of 8 ohms but where they differ is the sensitivity levels. SE 6000F sensitivity is rated at 93 dB and the RP-6000F's is at 97 dB. This 4 dB difference makes the Klipsch RP-6000F a more sensitive speaker compared to Paradigm SE 6000F, hence will play louder with the same amount of watts.
Sensitivity
Floor-standing Speakers
Power Range
Power
range is the range of input power in watts RMS that a loudspeaker is designed to handle. While using an amplifier within this range ensures the nominal performance , inputting a power that is higher than the max wattage can result in a damaged speaker.
SE 6000F can handle a max power of 125 watts RMS from the amp the whereas SE 6000F has a max power handling value of 100 watts RMS , 25 watts less than the RP-6000F.
Keep in mind that a higher max power handling value doesn't necessarily make that a louder speaker
compared to a lower max handling speaker. Loudness or the sound level is also impacted by parameters
such as Impedance, sensitivity and system efficiencies.
Input Type and Bi-Amping / Bi-Wiring
RP-6000F features Post posts which make bi-amping or bi-wiring possible. SE 6000F has a Post which doesn't feature bi-amping/bi-wiring.
Paradigm SE 6000F's Post terminals
Klipsch RP-6000F's Post terminals allows Bi-amping or bi-wiring
Cabinet Type and Port Position
Both SE 6000F and RP-6000F have rear firing ports. Rear ported speakers generally need more room between the backside of the speaker and the wall compared to sealed and front/bottom ported speakers. Placing the speakers too close to the walls may cause the bass to sound boomy.
If you are limited in space and can't get the speakers away from the backwall, check our Speakers with Front Firing Ports page.
Physical Specs
Size of a speaker can sometimes become an important decision factor due to space constraints or in some cases purely for esthetic reasons. In this section, we are going to compare Paradigm SE 6000F's and Klipsch RP-6000F's external dimensions. Paradigm SE 6000F has external dimensions of 1051.0 x 228.0 x 361.0mm ( 41-3/8 x 8-15/16 x 14-3/16inch) whereas Klipsch RP-6000F has external dimensions of 1010.0 x 237.0 x 432.0mm ( 39-3/4 x 9-5/16 x 17inch) .
Paradigm SE 6000F is 9mm narrower and 71mm less deeper than Klipsch RP-6000F but it is also 41mm taller.
Base Surface Area Comparison
Base surface area of a loudspeaker may become a determining factor when the space in your room or desk is limited.
The base surface area of the Paradigm SE 6000F is approximately 823.1cm2 / 127.6inch2 and base area of the Klipsch RP-6000F is approximately 1023.8cm2 / 158.7inch2. The SE 6000F requires 20% less surface area than the RP-6000F which gives it a small advantage on placement in tight spaces.
Weight Comparison The weight of a loudspeaker can become an important factor if you need to move and reposition the unit often. Weight of a speaker can also "sometimes" be an indicator of the rigidity of the enclosure and the quality of the internal components used. The Paradigm SE 6000F weighs 20.00kg / 44lbs and the Klipsch RP-6000F weighs 22.27kg / 49lbs. This makes the RP-6000F 11% heavier than the SE 6000F.
Here is a comparison of how SE 6000F and RP-6000F's weights compare with the average, max and min weights in Passive Floor-standing class.
Weight
All Floor-standing Speakers
What's in the Box of Paradigm SE 6000F?
Here are the items that are included inside the box of SE 6000F:
Floorstanding loudspeaker
4 Rubber feet
4 Spike feet
Owner's Manual
Online Registration Card
Unboxing Instructions
What's in the Box of Klipsch RP-6000F?
Here are the items that come with the RP-6000F:
Floorstanding loudspeakerStabilizer feet (installed)Grille (installed)2 Terminal jumpers (installed)User ManualImportant Safety InstructionsWarranty Information
 Driver Setup |
3-way
vs
2-way
|
Have a dedicated mid-range driver |
 Number of Woofers |
3
vs
2
|
More woofers |
 Base Surface Area |
823cm2 (228x361mm)
vs
1023cm2 (237x432mm)
|
Takes less floor space |
 Price per pair* |
1000USD
vs
1378USD
|
costs less (*prices may change depending on the seller, location and time) |
 Max Input Power |
125 watts
vs
100 watts
|
Handle more power from your amplifier |
 Sensitivity |
97 dB
vs
93 dB
|
Play louder with same amount of amplification power |
| Woofer Size |
6.5 inches
vs
5.5 inches
|
Larger woofer |
| Low Frequency Response |
34 Hz
vs
53 Hz
|
Generates deeper bass |
 High Frequency Response |
25k Hz
vs
21k Hz
|
Generates higher frequency |
 Bi-Amping and Bi-Wiring |
Yes
vs
No
|
Allows bi-amping and bi-wiring connections |
 Height |
1010mm
vs
1051mm
|
Easier to fit in smaller spaces |
| General |
Paradigm Monitor SE 6000F |
Klipsch Reference Premiere RP-6000F |
| Brand |
Paradigm |
Klipsch |
| Speaker Type |
Floor-standing speaker |
Floor-standing speaker |
| Power Range |
15-100 watts |
up to 125 watts |
| Sensitivity |
93 dB |
97 dB |
| Impedance |
8 ohms |
8 ohms |
| Frequency Response |
53-21k Hz |
34-25k Hz |
Drivers |
|
|
| Woofer Quantity |
3 |
2 |
| Woofer Size |
5.5" |
6.5" |
| Woofer Composition |
Mineral-filled polypropylene |
Cerametallic |
| Woofer Surround Material |
Rubber |
Rubber |
| Tweeter Size |
1" |
1" |
| Tweeter Type |
n/a |
Tractrix Horn |
| Aimable Tweeter |
No |
No |
| Midrange Driver |
5.5" |
No |
| Firing Direction |
rear |
rear |
Physical Specs |
|
|
| Height |
1051.0mm (41.4") |
1010.0mm (39.8") |
| Width |
228.0mm (9") |
237.0mm (9.3") |
| Depth |
361.0mm (14.2") |
432.0mm (17") |
| Weight |
20.00kg (44lbs) |
22.27kg (49lbs) |
| Enclosure |
Bass Reflex |
Bass Reflex |
| Finish |
MDF/Vinyl |
MDF/Wood-grain vinyl |
| Available Colors |
Black |
Walnut, Black |
| Grille |
n/a |
Yes |
| Moisture Resistancy |
No |
No |
Connections |
|
|
| Biamp Inputs |
No |
Yes |
Other |
|
|
| Parts Warranty |
5 Years |
5 Years |
| Labor Warranty |
5 Years |
5 Years |