In this review, we will be comparing Airmotiv XT1 and Airmotiv T1+, two Passive Floor-standing speakers by Emotiva Let's have a brief look at the main features
of Emotiva Airmotiv XT1 and Emotiva Airmotiv T1+ first before getting into our more
detailed comparison.
What size room are the Emotiva Airmotiv XT1 and Emotiva Airmotiv T1+ speakers good for?
The size of the room in which you are planning to use these loudspeakers is an important decision factor. Here we have compared their suitability to various sizes of environments considering their size and max power parameters:
In the following sections, we will get into more detail in order to better understand how the Emotiva Airmotiv XT1 and Emotiva Airmotiv T1+ compare and hopefully end up with enough arguments to decide which one of these loudspeakers is the better choice for you.
**This post contains affiliate links, and I will be compensated if you make a purchase after clicking
through my links. As an Amazon Associate I earn from qualifying purchases.
Drivers
Both Airmotiv XT1 and Airmotiv T1+ are 3-way speakers.
| Driver |
Emotiva Airmotiv XT1 |
Emotiva Airmotiv T1+ |
|
Driver Setup
|
3-way
|
3-way
|
|
Tweeter
|
25×32 mm-inch
|
25×32 mm-inch
|
|
Midrange
|
1 x 4.5-inch |
1 x 5.25-inch |
|
Woofer
|
3 x 5.25-inch
|
2 x 6-inch
|
Airmotiv XT1 features a 25×32 mm" folded ribbon Tweeter , a 4.5" Midrange and 3 x 5.25" woven fiber cone Woofer with a Crossover frequency at 410 Hz, 3.1 kHz. On the other hand, the Airmotiv T1+ features a 25×32 mm" folded ribbon Tweeter , a 5.25" Midrange and 2 x 6" woven fiber cone Woofer with a Crossover frequency at 275 Hz and 2700Hz.
Frequency Response
Airmotiv XT1 has a frequency range of 45 Hz – 27 kHz whereas Airmotiv T1+ has a frequency range of 37 Hz – 28 kHz. With a minimum frequency of 37Hz, the Airmotiv T1+ can go significantly deeper on the low side and provide stronger bass compared to the Airmotiv XT1's min frequency of 45Hz.
Below graphs depict how these two speakers compare with the max, min and average values of the Min and Max Frequencies of other speakers in the Floor-standing class in our database.
Low Frequency
Floor-standing Speakers
High Frequency
Floor-standing Speakers
None of these speakers achieves full range experience which is commonly agreed as 20Hz-20kHz. In order to achieve lower lows / deeper bass, we recommend you pair these with a subwoofer. Visit our Powered Subwoofers section to find out more about the available options.
Impedance and Sensitivity
Airmotiv XT1 and Airmotiv T1+ have the same Impedance of 4 ohms but where they differ is the sensitivity levels. Airmotiv XT1 sensitivity is rated at 89 dB and the Airmotiv T1+'s is at 88 dB. This 1 dB difference makes the Emotiva Airmotiv XT1 a more sensitive speaker compared to Emotiva Airmotiv T1+, hence will play louder with the same amount of watts.
One thing to keep in mind that the lower impedance speakers, especially the ones that are rated at 4 ohms may put more pressure on the amplifier unit comared to higher impedance speakers especially at high volume levels, so make sure the amp you pair with the Airmotiv XT1 and the Airmotiv XT1 can provide this impedance level.
Sensitivity
Floor-standing Speakers
Power Range
Power
range is the range of input power in watts RMS that a loudspeaker is designed to handle. While using an amplifier within this range ensures the nominal performance , inputting a power that is higher than the max wattage can result in a damaged speaker.
Airmotiv XT1 can handle a max power of 200 watts RMS from the amp the whereas Airmotiv T1+ has a max power handling value of 150 watts RMS, 50 watts less than the Airmotiv XT1.
Keep in mind that a higher max power handling value doesn't necessarily make that a louder speaker
compared to a lower max handling speaker. Loudness or the sound level is also impacted by parameters
such as Impedance, sensitivity and system efficiencies.
Input Type and Bi-Amping / Bi-Wiring
Both Airmotiv XT1 and Airmotiv T1+ features dual binding post speaker terminals for bi-amping or bi-wiring.
Emotiva Airmotiv XT1's Binding post terminals allows Bi-amping or bi-wiring
Emotiva Airmotiv T1+'s Binding post terminals allows Bi-amping or bi-wiring
Cabinet Type and Port Position
Both Airmotiv XT1 and Airmotiv T1+ have rear firing ports. Rear ported speakers generally need more room between the backside of the speaker and the wall compared to sealed and front/bottom ported speakers. Placing the speakers too close to the walls may cause the bass to sound boomy.
If you are limited in space and can't get the speakers away from the backwall, check our Speakers with Front Firing Ports page.
Emotiva Airmotiv T1+ Port
Physical Specs
Size of a speaker can sometimes become an important decision factor due to space constraints or in some cases purely for esthetic reasons. In this section, we are going to compare Emotiva Airmotiv XT1's and Emotiva Airmotiv T1+'s external dimensions. Emotiva Airmotiv XT1 has external dimensions of 106 x 178 x 254 mm ( 41.75” x 7” x 10”) whereas Emotiva Airmotiv T1+ has external dimensions of 1004.0 x 213.0 x 296.0mm ( 39-1/2 x 8-3/8 x 11-5/8inch) .
Emotiva Airmotiv T1+ is 9mm narrower and 56mm shorter than Emotiva Airmotiv XT1 but it is also 42mm deeper.
Base Surface Area Comparison
Base surface area of a loudspeaker may become a determining factor when the space in your room or desk is limited.
The base surface area of the Emotiva Airmotiv XT1 is approximately 452.1cm2 / 70.1inch2 and base area of the Emotiva Airmotiv T1+ is approximately 630.5cm2 / 97.7inch2. The Airmotiv XT1 requires 28% less surface area than the Airmotiv T1+ which gives it a small advantage on placement in tight spaces.
Weight Comparison The weight of a loudspeaker can become an important factor if you need to move and reposition the unit often. Weight of a speaker can also "sometimes" be an indicator of the rigidity of the enclosure and the quality of the internal components used. The Emotiva Airmotiv XT1 weighs 15.90kg / 35lbs and the Emotiva Airmotiv T1+ weighs 18.20kg / 40lbs. This makes the Airmotiv T1+ 14% heavier than the Airmotiv XT1.
Here is a comparison of how Airmotiv XT1 and Airmotiv T1+'s weights compare with the average, max and min weights in Passive Floor-standing class.
Weight
All Floor-standing Speakers
 Max Input Power |
200 watts
vs
150 watts
|
Handle more power from your amplifier |
 Sensitivity |
89 dB
vs
88 dB
|
Play louder with same amount of amplification power |
 Number of Woofers |
3
vs
2
|
More woofers |
 Base Surface Area |
452cm2 (222x254mm)
vs
630cm2 (213x296mm)
|
Takes less floor space |
| Woofer Size |
6 inches
vs
5.25 inches
|
Larger woofer |
| Low Frequency Response |
37 Hz
vs
45 Hz
|
Generates deeper bass |
 High Frequency Response |
28k Hz
vs
27k Hz
|
Generates higher frequency |
 Height |
1004mm
vs
1060mm
|
Easier to fit in smaller spaces |
 Price per pair* |
799USD
vs
999USD
|
costs less (*prices may change depending on the seller, location and time) |
| General |
Emotiva Airmotiv XT1 |
Emotiva Airmotiv T1+ |
| Brand |
Emotiva |
Emotiva |
| Speaker Type |
Floor-standing speaker |
Floor-standing speaker |
| Power Range |
Up to 200 watts |
Up to 150 watts |
| Sensitivity |
89 dB |
88 dB |
| Impedance |
4 ohms |
4 ohms |
| Frequency Response |
45 Hz – 27 kHz |
37 Hz – 28 kHz |
Drivers |
|
|
| Woofer Quantity |
3 |
2 |
| Woofer Size |
5.25" |
6" |
| Woofer Composition |
woven fiber cone |
woven fiber cone |
| Woofer Surround Material |
SBR |
n/a |
| Tweeter Size |
25×32 mm" |
25×32 mm" |
| Tweeter Type |
folded ribbon |
folded ribbon |
| Aimable Tweeter |
No |
No |
| Midrange Driver |
4.5" |
5.25" |
| Crossover Frequency |
410 Hz, 3.1 kHz |
275 Hz and 2700Hz |
| Firing Direction |
rear |
rear |
Physical Specs |
|
|
| Height |
1060.0mm (41.7") |
1004.0mm (39.5") |
| Width |
222.0mm (8.7") |
213.0mm (8.4") |
| Depth |
254.0mm (10") |
296.0mm (11.7") |
| Weight |
15.90kg (35lbs) |
18.20kg (40lbs) |
| Enclosure |
Bass reflex |
Bass reflex |
| Finish |
n/a |
HDF |
| Available Colors |
Black |
Black |
| Grille |
Yes |
Yes |
| Moisture Resistancy |
No |
No |
Connections |
|
|
| Biamp Inputs |
Yes |
Yes |
Other |
|
|
| Parts Warranty |
5 Years |
5 Years |
| Labor Warranty |
5 Years |
5 Years |