In this review, we will be comparing Gravis III and R-100SW, two Powered Subwoofer speakers from Sonus faber and Klipsch. Being Powered subwoofers, they both have built-in amplifiers so you don't need an external power amp or an integrated amp to power them. Let's have a brief look at the main features of Sonus faber Gravis III and Klipsch R-100SW first before getting into our more detailed comparison.
In the following sections, we will get into details in order to better understand how the Sonus faber Gravis III and Klipsch R-100SW compare and hopefully end up with enough arguments to decide which one of these subwoofers is the better choice for you.
**This post contains affiliate links, and I will be compensated if you make a purchase after clicking through my links. As an Amazon Associate I earn from qualifying purchases.
Drivers
The efficiency of a subwoofer is directly proportional to the total radiating are squared hence the woofer quantity and diameter.Sonus faber Gravis IIIand Klipsch R-100SW have the same driver set up: Both subwoofers have 1 x 10" drivers.
Frequency Response
Gravis III has a frequency range of 25-120 Hz whereas R-100SW has a frequency range of 32-120 Hz. With a minimum frequency of 25Hz, the Gravis III can go significantly deeper on the low side and provide stronger bass compared to the R-100SW's min frequency of 32Hz.
Below graphs depict how these two speakers compare with the max, min and average values of the Min and Max Frequencies of other speakers in the Subwoofer class in our database.
Low Frequency
Subwoofer Speakers
High Frequency
Subwoofer Speakers
Cabinet Type
The Sonus faber Gravis III has a Acoustic Suspension type cabinet. Acoustic Suspension aka Sealed type subwoofers have enclosures that are sealed hence no ports or holes exists on the cabinet. Sealed designs helps to provide more accurate and tight bass responses compared to ported designs. On the other hand the Klipsch R-100SW have Bass reflex type enclosure.
Physical Specs
Size of a speaker can sometimes become an important decision factor due to space constraints or in some cases purely for esthetic reasons. In this section, we are going to compare Sonus faber Gravis III's and Klipsch R-100SW's external dimensions. Sonus faber Gravis III has external dimensions of 415.0 x 400.0 x 495.0mm ( 16-5/16 x 15-3/4 x 19-1/2inch) whereas Klipsch R-100SW has external dimensions of 372.0 x 320.0 x 459.0mm ( 14-5/8 x 12-9/16 x 18-1/16inch) .
Sonus faber Gravis III is clearly the larger of the two speakers. Its body is 80mm wider, 43mm taller and 36mm deeper than Klipsch R-100SW.
Base Surface Area Comparison
Base surface area of a loudspeaker may become a determining factor when the space in your room or desk is limited.
The base surface area of the Sonus faber Gravis III is approximately 1980.0cm2 / 306.9inch2 and base area of the Klipsch R-100SW is approximately 1468.8cm2 / 227.7inch2. The Gravis III requires 35% more surface area than the R-100SW which gives it a small disadvantage on placement in tight spaces.
Weight Comparison The weight of a subwoofer may become an important factor if you need to move and reposition the unit often to find the optimal positioning, also known as 'Subwoofer Crawling'. The Sonus faber Gravis III weighs 26.70kg / 58.7lbs and the Klipsch R-100SW weighs 10.91kg / 24lbs. This makes the Gravis III 145% heavier than the R-100SW.
Here is a comparison of how Gravis III and R-100SW's weights compare with the average, max and min weights in Powered Subwoofer class.
Weight
All Subwoofer Speakers
 Low Frequency Response |
25 Hz
vs
32 Hz
|
Generates deeper bass |
 Height |
372mm
vs
415mm
|
Easier to fit in smaller spaces |
 Base Surface Area |
1468cm2
vs
1980cm2
|
Takes less floor space |
| General |
Sonus faber Gravis III |
Klipsch R-100SW |
| Brand |
Sonus faber |
Klipsch |
| Speaker Type |
Powered Subwoofer |
Powered Subwoofer |
| Max Amplifier Output |
600 watts |
150 watts |
| Frequency Response |
25-120 Hz |
32-120 Hz |
Amplifier |
|
|
| Watts RMS (Continuous) |
600-watt RMS |
150-watt RMS |
| Watts Peak (Max) |
900-watt RMS |
300-watt RMS |
Drivers |
|
|
| Woofer Quantity |
1 |
1 |
| Woofer Size |
10" |
10" |
| Woofer Composition |
Honeycomb sandwich |
Copper-spun IMG |
| Tweeter Size |
- |
- |
| Aimable Tweeter |
No |
No |
| Midrange Driver |
No |
No |
| Crossover Frequency |
Continuously adjustable |
n/a |
| Firing Direction |
n/a |
front |
Physical Specs |
|
|
| Height |
415.0mm (16.3") |
372.0mm (14.6") |
| Width |
400.0mm (15.7") |
320.0mm (12.6") |
| Depth |
495.0mm (19.5") |
459.0mm (18.1") |
| Weight |
26.70kg (58.7lbs) |
10.91kg (24lbs) |
| Enclosure |
Acoustic Suspension |
Bass reflex |
| Grille |
Yes |
Yes |
| Moisture Resistancy |
No |
No |
Connections |
|
|
Other |
|
|
| Parts Warranty |
|
2 Years |
| Labor Warranty |
|
2 Years |