In this review, we will be comparing SourcePoint 10 and R3, two Passive Bookshelf speakers from MoFi and KEF. Let's have a brief look at the main features
of MoFi SourcePoint 10 and KEF R3 first before getting into our more
detailed comparison.
What size room are the MoFi SourcePoint 10 and KEF R3 speakers good for?
The size of the room in which you are planning to use these loudspeakers is an important decision factor. Here we have compared their suitability to various sizes of environments considering their size and max power parameters:
In the following sections, we will get into more detail in order to better understand how the MoFi SourcePoint 10 and KEF R3 compare and hopefully end up with enough arguments to decide which one of these loudspeakers is the better choice for you.
**This post contains affiliate links, and I will be compensated if you make a purchase after clicking
through my links. As an Amazon Associate I earn from qualifying purchases.
Drivers
One of the fundamental differences between these two speakers is that SourcePoint 10 is a 2-way design whereas the R3 is a 3-way speaker. 3-way designs utilize a midrange driver in addition to the tweeter and woofer on 2-way designs. Designing a crossover for a 3-way speaker is a complicated process and generally increases the overall cost of the speaker.
| Driver |
MoFi SourcePoint 10 |
KEF R3 |
|
Driver Setup
|
2-way
|
3-way
|
|
Tweeter
|
1.25-inch
|
1-inch
|
|
Midrange
|
- |
1 x 5-inch |
|
Woofer
|
1 x 10-inch
|
1 x 6.5-inch
|
SourcePoint 10 features a 1.25" wide roll soft dome Tweeter and 1 x 10" Paper-pulp Woofer with a Crossover frequency at 1600 Hz. On the other hand, the R3 features a 1" aluminum Dome Tweeter , a 5" Midrange and 1 x 6.5" Hybrid aluminum Woofer with a Crossover frequency at 400Hz and 2900Hz.
Frequency Response
SourcePoint 10 has a frequency range of 42-30k Hz whereas R3 has a frequency range of 52-28k Hz. With a minimum frequency of 42Hz, the SourcePoint 10 can go significantly deeper on the low side and provide stronger bass compared to the R3's min frequency of 52Hz.
Below graphs depict how these two speakers compare with the max, min and average values of the Min and Max Frequencies of other speakers in the Bookshelf class in our database.
Low Frequency
Bookshelf Speakers
High Frequency
Bookshelf Speakers
None of these speakers achieves full range experience which is commonly agreed as 20Hz-20kHz. In order to achieve lower lows / deeper bass, we recommend you pair these with a subwoofer. Visit our Powered Subwoofers section to find out more about the available options.
Impedance and Sensitivity
SourcePoint 10 and R3 have the same Impedance of 8 ohms but where they differ is the sensitivity levels. SourcePoint 10 sensitivity is rated at 91dB and the R3's is at 87 dB. This 4 dB difference makes the MoFi SourcePoint 10 a more sensitive speaker compared to KEF R3, hence will play louder with the same amount of watts.
Sensitivity
Bookshelf Speakers
Power Range
Power
range is the range of input power in watts RMS that a loudspeaker is designed to handle. While using an amplifier within this range ensures the nominal performance , inputting a power that is higher than the max wattage can result in a damaged speaker.
SourcePoint 10 can handle a max power of 200 watts RMS from the amp the whereas R3 has a max power handling value of 180 watts RMS, 20 watts less than the SourcePoint 10.
Keep in mind that a higher max power handling value doesn't necessarily make that a louder speaker
compared to a lower max handling speaker. Loudness or the sound level is also impacted by parameters
such as Impedance, sensitivity and system efficiencies.
Input Type and Bi-Amping / Bi-Wiring
R3 features Binding post posts which make bi-amping or bi-wiring possible. SourcePoint 10 has a 5-Way post which doesn't feature bi-amping/bi-wiring.
MoFi SourcePoint 10's 5-Way post terminals
Cabinet Type and Port Position
Both SourcePoint 10 and R3 have rear firing ports. Rear ported speakers generally need more room between the backside of the speaker and the wall compared to sealed and front/bottom ported speakers. Placing the speakers too close to the walls may cause the bass to sound boomy.
If you are limited in space and can't get the speakers away from the backwall, check our Speakers with Front Firing Ports page.
KEF R3 Port
Physical Specs
Size of a speaker can sometimes become an important decision factor due to space constraints or in some cases purely for esthetic reasons. In this section, we are going to compare MoFi SourcePoint 10's and KEF R3's external dimensions. MoFi SourcePoint 10 has external dimensions of 572 x 368 x 406mm ( 22.5 x 14.5 x 16 inch) whereas KEF R3 has external dimensions of 423.0 x 199.0 x 337.0mm ( 16-5/8 x 7-13/16 x 13-1/4inch) .
MoFi SourcePoint 10 is clearly the larger of the two speakers. Its body is 169mm wider, 149mm taller and 85mm deeper than KEF R3.
Below you can see the front view size comparison of MoFi SourcePoint 10 and KEF R3 in scale.
Comparison image of MoFi SourcePoint 10 and KEF R3 Size and External Dimensions
Base Surface Area Comparison
Base surface area of a loudspeaker may become a determining factor when the space in your room or desk is limited.
The base surface area of the MoFi SourcePoint 10 is approximately 1552.0cm2 / 240.6inch2 and base area of the KEF R3 is approximately 670.6cm2 / 103.9inch2. The SourcePoint 10 requires 131% more surface area than the R3 which gives it a small disadvantage on placement in tight spaces.
Weight Comparison The weight of a loudspeaker can become an important factor if you need to move and reposition the unit often. Weight of a speaker can also "sometimes" be an indicator of the rigidity of the enclosure and the quality of the internal components used. The MoFi SourcePoint 10 weighs 21.00kg / 46.2lbs and the KEF R3 weighs 13.55kg / 29.8lbs. This makes the SourcePoint 10 55% heavier than the R3.
Here is a comparison of how SourcePoint 10 and R3's weights compare with the average, max and min weights in Passive Bookshelf class.
Weight
All Bookshelf Speakers
What's in the Box of KEF R3?
Here are the items that come with the R3:
2 Bookshelf loudspeakers2 Grilles2 Foam port plugs8 Self-adhesive rubber feetUser ManualWarranty Information
 Max Input Power |
200 watts
vs
180 watts
|
Handle more power from your amplifier |
 Sensitivity |
91 dB
vs
87 dB
|
Play louder with same amount of amplification power |
 Minimum Impedance |
6.2 ohms
vs
3.2 ohms
|
Very low impedance levels puts more pressure on amplifier |
 Woofer Size |
10 inches
vs
6.5 inches
|
Larger woofer |
| Low Frequency Response |
42 Hz
vs
52 Hz
|
Generates deeper bass |
 High Frequency Response |
30k Hz
vs
28k Hz
|
Generates higher frequency |
 Driver Setup |
3-way
vs
2-way
|
Have a dedicated mid-range driver |
 Bi-Amping and Bi-Wiring |
Yes
vs
No
|
Allows bi-amping and bi-wiring connections |
 Height |
423mm
vs
572mm
|
Easier to fit in smaller spaces |
 Base Surface Area |
670cm2 (199x337mm)
vs
1552cm2 (368x422mm)
|
Takes less floor space |
 Price per pair* |
2200USD
vs
3699USD
|
costs less (*prices may change depending on the seller, location and time) |
| General |
MoFi SourcePoint 10 |
KEF R3 |
| Brand |
MoFi |
KEF |
| Speaker Type |
Bookshelf speakers |
Bookshelf speakers |
| Power Range |
30-200 watts |
15-180 watts |
| Sensitivity |
91dB |
87 dB |
| Impedance |
8 ohms |
8 ohms |
| Impedance |
6.2 ohms |
3.2 ohms |
| Frequency Response |
42-30k Hz |
52-28k Hz |
Drivers |
|
|
| Woofer Quantity |
1 |
1 |
| Woofer Size |
10" |
6.5" |
| Woofer Composition |
Paper-pulp |
Hybrid aluminum |
| Woofer Surround Material |
n/a |
Rubber |
| Tweeter Size |
1.25" |
1" |
| Tweeter Type |
wide roll soft dome |
Dome |
| Aimable Tweeter |
No |
No |
| Midrange Driver |
No |
5" |
| Crossover Frequency |
1600 Hz |
400Hz and 2900Hz |
| Firing Direction |
rear |
rear |
Physical Specs |
|
|
| Height |
572.0mm (22.5") |
423.0mm (16.7") |
| Width |
368.0mm (14.5") |
199.0mm (7.8") |
| Depth |
422.0mm (16.6") |
337.0mm (13.3") |
| Weight |
21.00kg (46.2lbs) |
13.55kg (29.8lbs) |
| Enclosure |
Bass Reflex |
Bass Reflex |
| Finish |
real wood veneer |
MDF/Lacquer |
| Available Colors |
Satin Walnut, Satin Black Ash |
Black Gloss, White Gloss, Walnut |
| Mounting Bracket |
No |
No |
| Grille |
Yes |
Yes |
| Moisture Resistancy |
No |
No |
Connections |
|
|
| Biamp Inputs |
No |
Yes |
Other |
|
|
| Parts Warranty |
|
5 Years |
| Labor Warranty |
|
5 Years |