In this review, we will be comparing R-5502-W II and RC65i, two Passive In-wall speakers from Klipsch and Polk Audio.
Let's have a brief look at the main features
of Klipsch R-5502-W II and Polk Audio RC65i first before getting into our more
detailed comparison.
Klipsch R-5502-W II Key Specs
- 2-way Design
- 1" Horn-loaded Tweeter
- 2 x 5.25" Cerametallic Woofer
- 46-20kHz Frequency Response
- 92 dB Sensitivity
- Impedance: 8ohms
- Power Range:up to 75watts
- Dimensions (H x W x D): 416.0" x 6.5000" x 3.3750"( 416.0 x 166.0 x 86.0mm )
Polk Audio RC65i Key Specs
- 2-way Design
- 0.75" Hard-Dome Tweeter
- 6.5" Polypropylene Woofer
- 60-20kHz Frequency Response
- 89 dB Sensitivity
- Impedance: 8ohms
- Power Range:20-100watts
- Dimensions (H x W x D): 274.0" x 7.3125" x 2.4070"( 274.0 x 186.0 x 62.0mm )
What size room are the Klipsch R-5502-W II and Polk Audio RC65i speakers good for?
The size of the room in which you are planning to use these loudspeakers is an important decision
factor. Here we have compared their suitability to various sizes of environments considering their size
and max power parameters:
| Listening Environment* |
Klipsch R-5502-W II |
Polk Audio RC65i |
| Near-field |
Good |
Average |
| Small Room |
Good |
Good |
| Mid-size Room |
Average |
Average |
| Large Room |
Poor |
Poor |
| Very Large Room |
No way |
Bad |
(* Approximate Room sizes: Small < 100sq. ft / 9 m2,
Mid-size: 100-220 sq. ft / 9-20 m2, Large 220-400 sq. ft / 20-36 m2, Very Large: >
400 sq. ft / 36 m2.
Average Floor Height: 9" / 2.7m. Typical room sizes differ from country to country, and the actual
listening experience changes depending on floor height, room shape, surface materials, listening
position, speaker locations, etc.)
In the following sections, we will get into more detail in order to better understand how the Klipsch R-5502-W II and Polk Audio RC65i compare and hopefully end up with enough arguments to decide which one of these loudspeakers is the better choice for you.
**This post contains affiliate links, and I will be compensated if you make a purchase after clicking
through my links. As an Amazon Associate I earn from qualifying purchases.
Drivers
Both R-5502-W II and RC65i are 2-way speakers.
| Driver |
Klipsch R-5502-W II |
Polk Audio RC65i |
|
Driver Setup
|
2-way
|
2-way
|
|
Tweeter
|
1-inch
|
0.75-inch
|
|
Midrange
|
- |
- |
|
Woofer
|
2 x 5.25-inch
|
1 x 6.5-inch
|
R-5502-W II features a 1" Horn-loaded Tweeter and 2 x 5.25" Cerametallic Woofer . On the other hand, the RC65i features a 0.75" Hard-Dome Tweeter and 1 x 6.5" Polypropylene Woofer .
Frequency Response
R-5502-W II has a frequency range of 46-20kHz whereas RC65i has a frequency range of 60-20kHz. With a minimum frequency of 46Hz, the R-5502-W II can go significantly deeper on the low side and provide stronger bass compared to the RC65i's min frequency of 60Hz.
Below graphs depict how these two speakers compare with the max, min and average values of the Min and Max Frequencies of other speakers in the In-wall class in our database.
Low Frequency
In-wall Speakers
High Frequency
In-wall Speakers
None of these speakers achieves full range experience which is commonly agreed as 20Hz-20kHz. In order to achieve lower lows / deeper bass, we recommend you pair these with a subwoofer. Visit our Powered Subwoofers section to find out more about the available options.
Impedance and Sensitivity
R-5502-W II and RC65i have the same Impedance of 8 ohms but where they differ is the sensitivity levels. R-5502-W II sensitivity is rated at 92 dB and the RC65i's is at 89 dB. This 3 dB difference makes the Klipsch R-5502-W II a more sensitive speaker compared to Polk Audio RC65i, hence will play louder with the same amount of watts.
Sensitivity
In-wall Speakers
Power Range
Power
range is the range of input power in watts RMS that a loudspeaker is designed to handle. While using
an amplifier within this range ensures the nominal performance , inputting a power that is higher than the
max wattage can result in a damaged speaker.
R-5502-W II can handle a max power of 100 watts RMS from the amp the whereas R-5502-W II has a max power handling value of 75 watts RMS , 25 watts less than the RC65i.
Keep in mind that a higher max power handling value doesn't necessarily make that a louder speaker
compared to a lower max handling speaker. Loudness or the sound level is also impacted by parameters
such as Impedance, sensitivity and system efficiencies.
Input Type and Bi-Amping / Bi-Wiring
R-5502-W II features Spring clip type posts and RC65i has a Spring clip type posts. None of these speakers feature bi-amping/bi-wiring.
Physical Specs
Size of a speaker can sometimes become an important decision factor due to space constraints or in some cases purely for esthetic reasons. In this section, we are going to compare Klipsch R-5502-W II's and Polk Audio RC65i's external dimensions. Klipsch R-5502-W II has external dimensions of 416.0 x 166.0 x 86.0mm ( 16.3750-inch x 6.5000-inch x 3.3750-inch) whereas Polk Audio RC65i has external dimensions of 274.0 x 186.0 x 62.0mm ( 10.7500-inch x 7.3125-inch x 2.4070-inch) .
Polk Audio RC65i is 142mm shorter and 24mm less deeper than Klipsch R-5502-W II but it is also 20mm wider.
What's in the Box of Klipsch R-5502-W II?
Here are the items that are included inside the box of R-5502-W II:
In-wall speakerWhite metal mesh grilleCardboard templateOwners Manual (En/Fr/Sp)
What's in the Box of Polk Audio RC65i?
Here are the items that come with the RC65i:
2 White in-wall speakers2 White grilles1 Cardboard Mounting TemplateOwners ManualOnline registration sheetProduct Registration Card