In this review, we will be comparing 702 S3 and Motion 60XTi, two Passive Floor-standing speakers from Bowers Wilkins and MartinLogan.
Let's have a brief look at the main features
of B&W 702 S3 and MartinLogan 60XTi first before getting into our more
detailed comparison.
B&W 702 S3 Key Specs
- 3-way Design
- 1" Tweeter
- 6" Midrange
- 3 x 6.5" Aerofoil Woofer
- 46-28k Hz Frequency Response
- 90 dB Sensitivity
- Impedance: 8ohms
- Power Range:30-300watts
- Weight:33.46kg
- Dimensions (H x W x D): 1138.0" x 7.6" x 15.4"( 1138.0 x 192.0 x 391.0mm )
MartinLogan 60XTi Key Specs
- 3-way Design
- 1.25 x 2.4" Folded Motion XT Tweeter
- 6.5" Midrange
- 2 x 8" Aluminum Woofer
- 6.5" Midrange
- 35-25k Hz Frequency Response
- 94 dB Sensitivity
- Impedance: 4ohms
- Power Range:20-400watts
- Weight:30.00kg
- Dimensions (H x W x D): 1174.0" x 9-1/16" x 15-9/16"( 1174.0 x 231.0 x 396.0mm )
What size room are the B&W 702 S3 and MartinLogan 60XTi speakers good for?
The size of the room in which you are planning to use these loudspeakers is an important decision
factor. Here we have compared their suitability to various sizes of environments considering their size
and max power parameters:
| Listening Environment* |
B&W 702 S3 |
MartinLogan 60XTi |
| Near-field |
Bad |
Are you nuts? |
| Small Room |
Poor |
Poor |
| Mid-size Room |
Average |
Average |
| Large Room |
Good |
Good |
| Very Large Room |
Average |
Good |
(* Approximate Room sizes: Small < 100sq. ft / 9 m2,
Mid-size: 100-220 sq. ft / 9-20 m2, Large 220-400 sq. ft / 20-36 m2, Very Large: >
400 sq. ft / 36 m2.
Average Floor Height: 9" / 2.7m. Typical room sizes differ from country to country, and the actual
listening experience changes depending on floor height, room shape, surface materials, listening
position, speaker locations, etc.)
In the following sections, we will get into more detail in order to better understand how the B&W 702 S3 and MartinLogan 60XTi compare and hopefully end up with enough arguments to decide which one of these loudspeakers is the better choice for you.
**This post contains affiliate links, and I will be compensated if you make a purchase after clicking
through my links. As an Amazon Associate I earn from qualifying purchases.
Drivers
Both 702 S3 and Motion 60XTi are 3-way speakers.
| Driver |
B&W 702 S3 |
MartinLogan 60XTi |
|
Driver Setup
|
3-way
|
3-way
|
|
Tweeter
|
1-inch
|
1.25 x 2.4-inch
|
|
Midrange
|
1 x 6-inch |
1 x 6.5-inch |
|
Woofer
|
3 x 6.5-inch
|
2 x 8-inch
|
702 S3 features a 1" Tweeter , a 6" Midrange and 3 x 6.5" Aerofoil Woofer . On the other hand, the Motion 60XTi features a 1.25 x 2.4" Folded Motion XT Tweeter , a 6.5" Midrange and 2 x 8" Aluminum Woofer with a Crossover frequency at 400Hz and 2200Hz.
Frequency Response
702 S3 has a frequency range of 46-28k Hz whereas Motion 60XTi has a frequency range of 35-25k Hz. With a minimum frequency of 35Hz, the Motion 60XTi can go significantly deeper on the low side and provide stronger bass compared to the 702 S3's min frequency of 46Hz.
Below graphs depict how these two speakers compare with the max, min and average values of the Min and Max Frequencies of other speakers in the Floor-standing class in our database.
Low Frequency
Floor-standing Speakers
High Frequency
Floor-standing Speakers
None of these speakers achieves full range experience which is commonly agreed as 20Hz-20kHz. In order to achieve lower lows / deeper bass, we recommend you pair these with a subwoofer. Visit our Powered Subwoofers section to find out more about the available options.
Impedance and Sensitivity
702 S3 is a 8 ohms speaker compared to the Motion 60XTi which has a nominal impedance of 4 ohms. Lower impedance speakers, especially the ones that are rated at 4 ohms may put more pressure on the amplifier unit especially when played at high volume levels, so make sure the amp you pair with the Motion 60XTi can provide this impedance level.
These two speakers also have different sensitivity levels. 702 S3 sensitivity is rated at 90 dB and the Motion 60XTi's is rated at 94 dB. This 6 dB difference makes the MartinLogan 60XTi a more sensitive speaker compared to B&W 702 S3, hence will play louder with the same amount of watts.
Sensitivity
Floor-standing Speakers
Power Range
Power
range is the range of input power in watts RMS that a loudspeaker is designed to handle. While using
an amplifier within this range ensures the nominal performance , inputting a power that is higher than the
max wattage can result in a damaged speaker.
702 S3 can handle a max power of 400 watts RMS from the amp the whereas 702 S3 has a max power handling value of 300 watts RMS , 100 watts less than the Motion 60XTi.
Keep in mind that a higher max power handling value doesn't necessarily make that a louder speaker
compared to a lower max handling speaker. Loudness or the sound level is also impacted by parameters
such as Impedance, sensitivity and system efficiencies.
Input Type and Bi-Amping / Bi-Wiring
Both 702 S3 and Motion 60XTi features dual binding post speaker terminals for bi-amping or bi-wiring.
B&W 702 S3's Binding post terminals allows Bi-amping or bi-wiring
MartinLogan 60XTi's Custom 5-way bi-wire tool-less binding posts terminals allows Bi-amping or bi-wiring
Cabinet Type and Port Position
Both 702 S3 and Motion 60XTi have rear firing ports. Rear ported speakers generally need more room between the backside of the speaker and the wall compared to sealed and front/bottom ported speakers. Placing the speakers too close to the walls may cause the bass to sound boomy.
If you are limited in space and can't get the speakers away from the backwall, check our Speakers with Front Firing Ports page.
Physical Specs
Size of a speaker can sometimes become an important decision factor due to space constraints or in some cases purely for esthetic reasons. In this section, we are going to compare B&W 702 S3's and MartinLogan 60XTi's external dimensions. B&W 702 S3 has external dimensions of 1138.0 x 192.0 x 391.0mm ( 44.8-inch x 7.6-inch x 15.4-inch) whereas MartinLogan 60XTi has external dimensions of 1174.0 x 231.0 x 396.0mm ( 46-3/16 x 9-1/16 x 15-9/16inch) .
MartinLogan 60XTi is clearly the larger of the two speakers. Its body is 39mm wider, 36mm taller and 5mm deeper than B&W 702 S3.
Below you can see the front view size comparison of B&W 702 S3 and MartinLogan 60XTi in scale.
Comparison image of B&W 702 S3 and MartinLogan 60XTi Size and External Dimensions
Base Surface Area Comparison
Base surface area of a loudspeaker may become a determining factor when the space in your room or desk is limited.
The base surface area of the B&W 702 S3 is approximately 750.7cm2 / 116.4inch2 and base area of the MartinLogan 60XTi is approximately 914.8cm2 / 141.8inch2. The 702 S3 requires 18% less surface area than the Motion 60XTi which gives it a small advantage on placement in tight spaces.