In this review, we will be comparing Gravis I and RP-1200SW, two Powered Subwoofer speakers from Sonus Faber and Klipsch. Being Powered subwoofers, they both have built-in amplifiers so you don't need an external power amp or an integrated amp to power them. Let's have a brief look at the main features of Sonus faber Gravis I and Klipsch RP-1200SW first before getting into our more detailed comparison.
In the following sections, we will get into details in order to better understand how the Sonus faber Gravis I and Klipsch RP-1200SW compare and hopefully end up with enough arguments to decide which one of these subwoofers is the better choice for you.
**This post contains affiliate links, and I will be compensated if you make a purchase after clicking through my links. As an Amazon Associate I earn from qualifying purchases.
Drivers
The efficiency of a subwoofer is directly proportional to the total radiating are squared hence the woofer quantity and diameter.Both Sonus faber Gravis Iand Klipsch RP-1200SW have a single woofer setup however the Sonus faber Gravis I's woofer is 8-inch whereas the Klipsch RP-1200SW features a 12-inch woofer.
Frequency Response
Gravis I has a frequency range of 30-120 Hz whereas RP-1200SW has a frequency range of 16.5-138 Hz. With a minimum frequency of 17Hz, the RP-1200SW can go significantly deeper on the low side and provide stronger bass compared to the Gravis I's min frequency of 30Hz.
Below graphs depict how these two speakers compare with the max, min and average values of the Min and Max Frequencies of other speakers in the Subwoofer class in our database.
Low Frequency
Subwoofer Speakers
High Frequency
Subwoofer Speakers
Cabinet Type
The Sonus faber Gravis I has a Acoustic Suspension type cabinet. Acoustic Suspension aka Sealed type subwoofers have enclosures that are sealed hence no ports or holes exists on the cabinet. Sealed designs helps to provide more accurate and tight bass responses compared to ported designs. On the other hand the Klipsch RP-1200SW have Bass Reflex type enclosure. Bass Reflex type subwoofers (aka Ported, Vented or Reflex Port) have enclosures that uses a port, hole or vent cut into the cabinet. Ported designs are generally more efficient than the Sealed designs.
Physical Specs
Size of a speaker can sometimes become an important decision factor due to space constraints or in some cases purely for esthetic reasons. In this section, we are going to compare Sonus faber Gravis I's and Klipsch RP-1200SW's external dimensions. Sonus faber Gravis I has external dimensions of 337.0 x 286.0 x 340.0mm ( 13-1/4inch x 11-1/4inch x 13-3/8inch ) whereas Klipsch RP-1200SW has external dimensions of 482.0 x 432.0 x 659.0mm ( 18-15/16inch x 17inch x 25-15/16inch ) .
Klipsch RP-1200SW is clearly the larger of the two speakers. Its body is 146mm wider, 145mm taller and 319mm deeper than Sonus faber Gravis I.
Base Surface Area Comparison
Base surface area of a loudspeaker may become a determining factor when the space in your room or desk is limited.
The base surface area of the Sonus faber Gravis I is approximately 972.4cm2 / 150.7inch2 and base area of the Klipsch RP-1200SW is approximately 2846.9cm2 / 441.3inch2. The Gravis I requires 66% less surface area than the RP-1200SW which gives it a small advantage on placement in tight spaces.
Weight Comparison The weight of a subwoofer may become an important factor if you need to move and reposition the unit often to find the optimal positioning, also known as 'Subwoofer Crawling'. The Sonus faber Gravis I weighs 14.55kg / 32lbs and the Klipsch RP-1200SW weighs 31.18kg / 68.6lbs. This makes the RP-1200SW 114% heavier than the Gravis I.
Here is a comparison of how Gravis I and RP-1200SW's weights compare with the average, max and min weights in Powered Subwoofer class.
Weight
All Subwoofer Speakers
 Height |
337mm
vs
482mm
|
Easier to fit in smaller spaces |
 Base Surface Area |
972cm2 (286x340mm)
vs
2846cm2 (432x659mm)
|
Takes less floor space |
 Driver Setup |
1-way
vs
-way
|
Have a dedicated mid-range driver |
 Woofer Size |
12 inches
vs
8 inches
|
Larger woofer |
| Low Frequency Response |
17 Hz
vs
30 Hz
|
Generates deeper bass |
 High Frequency Response |
138k Hz
vs
120k Hz
|
Generates higher frequency |
 Wireless Operation |
Optional
vs
No
|
Connect your subwoofer to your system wireless |
| General |
Sonus faber Gravis I |
Klipsch Reference Premiere RP-1200SW |
| Brand |
Sonus Faber |
Klipsch |
| Speaker Type |
Powered Subwoofer |
Powered Subwoofer |
| Max Amplifier Output |
150 watts |
400 watts |
| Frequency Response |
30-120 Hz |
16.5-138 Hz |
Amplifier |
|
|
| Watts RMS (Continuous) |
150-watt RMS |
400-watt RMS |
| Watts Peak (Max) |
n/a |
800-watt RMS |
Drivers |
|
|
| Woofer Quantity |
1 |
1 |
| Woofer Size |
8" |
12" |
| Woofer Composition |
Treated Paper |
Cerametallic |
| Tweeter Size |
- |
- |
| Aimable Tweeter |
No |
No |
| Midrange Driver |
No |
No |
| Firing Direction |
bottom |
front |
Physical Specs |
|
|
| Height |
337.0mm (13.3") |
482.0mm (19") |
| Width |
286.0mm (11.3") |
432.0mm (17") |
| Depth |
340.0mm (13.4") |
659.0mm (25.9") |
| Weight |
14.55kg (32lbs) |
31.18kg (68.6lbs) |
| Enclosure |
Acoustic Suspension |
Bass Reflex |
| Finish |
n/a |
MDF with Vinyl |
| Available Colors |
Piano Black,Matte White |
Ebony |
| Grille |
Yes |
Yes |
| Moisture Resistancy |
No |
No |
Connections |
|
|
Other |
|
|
| Parts Warranty |
2 Yr/3 Yr registered |
5 years |
| Labor Warranty |
2 Yr/3 Yr registered |
5 years |