In this review, we will be comparing Airmotiv T1+ and R-610F, two Passive Floor-standing speakers from Emotiva and Klipsch. Let's have a brief look at the main features
of Emotiva Airmotiv T1+ and Klipsch R-610F first before getting into our more
detailed comparison.
What size room are the Emotiva Airmotiv T1+ and Klipsch R-610F speakers good for?
The size of the room in which you are planning to use these loudspeakers is an important decision factor. Here we have compared their suitability to various sizes of environments considering their size and max power parameters:
In the following sections, we will get into more detail in order to better understand how the Emotiva Airmotiv T1+ and Klipsch R-610F compare and hopefully end up with enough arguments to decide which one of these loudspeakers is the better choice for you.
**This post contains affiliate links, and I will be compensated if you make a purchase after clicking
through my links. As an Amazon Associate I earn from qualifying purchases.
Drivers
One of the fundamental differences between these two speakers is that Airmotiv T1+ is a 3-way design whereas the R-610F is a 2-way speaker. 3-way designs utilize a midrange driver in addition to the tweeter and woofer on 2-way designs. Designing a crossover for a 3-way speaker is a complicated process and generally increases the overall cost of the speaker.
Driver |
Emotiva Airmotiv T1+ |
Klipsch R-610F |
Driver Setup
|
3-way
|
2-way
|
Tweeter
|
25×32 mm-inch
|
1.0-inch
|
Midrange
|
1 x 5.25-inch |
- |
Woofer
|
2 x 6-inch
|
1 x 6.5-inch
|
Airmotiv T1+ features a 25×32 mm" folded ribbon Tweeter , a 5.25" Midrange and 2 x 6" woven fiber cone Woofer with a Crossover frequency at 275 Hz and 2700Hz. On the other hand, the R-610F features a 1.0" Tweeter and 1 x 6.5" Copper-spun IMG Woofer .
Frequency Response
Airmotiv T1+ has a frequency range of 37 Hz – 28 kHz whereas R-610F has a frequency range of 45-21k Hz. With a minimum frequency of 37Hz, the Airmotiv T1+ can go significantly deeper on the low side and provide stronger bass compared to the R-610F's min frequency of 45Hz.
Below graphs depict how these two speakers compare with the max, min and average values of the Min and Max Frequencies of other speakers in the Floor-standing class in our database.
Low Frequency
Floor-standing Speakers
High Frequency
Floor-standing Speakers
None of these speakers achieves full range experience which is commonly agreed as 20Hz-20kHz. In order to achieve lower lows / deeper bass, we recommend you pair these with a subwoofer. Visit our Powered Subwoofers section to find out more about the available options.
Impedance and Sensitivity
Airmotiv T1+ is a 4 ohms speaker compared to the R-610F which has a nominal impedance of 8 ohms. Lower impedance speakers, especially the ones that are rated at 4 ohms may put more pressure on the amplifier unit especially when played at high volume levels, so make sure the amp you pair with the Airmotiv T1+ can provide this impedance level.
These two speakers also have different sensitivity levels. Airmotiv T1+ sensitivity is rated at 88 dB and the R-610F's is rated at 94 dB. This 6 dB difference makes the Klipsch R-610F a more sensitive speaker compared to Emotiva Airmotiv T1+, hence will play louder with the same amount of watts.
Sensitivity
Floor-standing Speakers
Power Range
Power
range is the range of input power in watts RMS that a loudspeaker is designed to handle. While using an amplifier within this range ensures the nominal performance , inputting a power that is higher than the max wattage can result in a damaged speaker.
Airmotiv T1+ can handle a max power of 150 watts RMS from the amp the whereas R-610F has a max power handling value of 85 watts RMS, 65 watts less than the Airmotiv T1+.
Keep in mind that a higher max power handling value doesn't necessarily make that a louder speaker
compared to a lower max handling speaker. Loudness or the sound level is also impacted by parameters
such as Impedance, sensitivity and system efficiencies.
Input Type and Bi-Amping / Bi-Wiring
Airmotiv T1+ features Binding post posts which make bi-amping or bi-wiring possible. R-610F has a Post which doesn't feature bi-amping/bi-wiring.
Cabinet Type and Port Position
Both Airmotiv T1+ and R-610F have rear firing ports. Rear ported speakers generally need more room between the backside of the speaker and the wall compared to sealed and front/bottom ported speakers. Placing the speakers too close to the walls may cause the bass to sound boomy.
If you are limited in space and can't get the speakers away from the backwall, check our Speakers with Front Firing Ports page.
Physical Specs
Size of a speaker can sometimes become an important decision factor due to space constraints or in some cases purely for esthetic reasons. In this section, we are going to compare Emotiva Airmotiv T1+'s and Klipsch R-610F's external dimensions. Emotiva Airmotiv T1+ has external dimensions of 1004.0 x 213.0 x 296.0mm ( 39-1/2 x 8-3/8 x 11-5/8inch) whereas Klipsch R-610F has external dimensions of 942.0 x 239.0 x 369.0mm ( 37-1/16 x 9-3/8 x 14-1/2inch) .
Emotiva Airmotiv T1+ is 26mm narrower and 73mm less deeper than Klipsch R-610F but it is also 62mm taller.
Base Surface Area Comparison
Base surface area of a loudspeaker may become a determining factor when the space in your room or desk is limited.
The base surface area of the Emotiva Airmotiv T1+ is approximately 630.5cm2 / 97.7inch2 and base area of the Klipsch R-610F is approximately 881.9cm2 / 136.7inch2. The Airmotiv T1+ requires 29% less surface area than the R-610F which gives it a small advantage on placement in tight spaces.
Weight Comparison The weight of a loudspeaker can become an important factor if you need to move and reposition the unit often. Weight of a speaker can also "sometimes" be an indicator of the rigidity of the enclosure and the quality of the internal components used. The Emotiva Airmotiv T1+ weighs 18.20kg / 40lbs and the Klipsch R-610F weighs 16.36kg / 36lbs. This makes the Airmotiv T1+ 11% heavier than the R-610F.
Here is a comparison of how Airmotiv T1+ and R-610F's weights compare with the average, max and min weights in Passive Floor-standing class.
Weight
All Floor-standing Speakers
What's in the Box of Klipsch R-610F?
Here are the items that come with the R-610F:
Floorstanding loudspeakerGrille (installed)2 Feet4 ScrewsQuick Setup GuideImportant Safety InstructionsWarranty InformationLoudspeaker Feet note
Max Input Power |
150 watts
vs
85 watts
|
Handle more power from your amplifier |
Driver Setup |
3-way
vs
2-way
|
Have a dedicated mid-range driver |
Number of Woofers |
2
vs
1
|
More woofers |
Low Frequency Response |
37 Hz
vs
45 Hz
|
Generates deeper bass |
High Frequency Response |
28k Hz
vs
21k Hz
|
Generates higher frequency |
Bi-Amping and Bi-Wiring |
Yes
vs
No
|
Allows bi-amping and bi-wiring connections |
Base Surface Area |
630cm2 (213x296mm)
vs
881cm2 (239x369mm)
|
Takes less floor space |
Sensitivity |
94 dB
vs
88 dB
|
Play louder with same amount of amplification power |
Nominal Impedance |
8 ohms
vs
4 ohms
|
Less selective with amplifiers |
Woofer Size |
6.5 inches
vs
6 inches
|
Larger woofer |
Height |
942mm
vs
1004mm
|
Easier to fit in smaller spaces |
Price per pair* |
778USD
vs
799USD
|
costs less (*prices may change depending on the seller, location and time) |
General |
Emotiva Airmotiv T1+ |
Klipsch Reference R-610F |
Brand |
Emotiva |
Klipsch |
Speaker Type |
Floor-standing speaker |
Floor-standing speaker |
Power Range |
Up to 150 watts |
up to 85 watts |
Sensitivity |
88 dB |
94 dB |
Impedance |
4 ohms |
8 ohms |
Frequency Response |
37 Hz – 28 kHz |
45-21k Hz |
Drivers |
|
|
Woofer Quantity |
2 |
1 |
Woofer Size |
6" |
6.5" |
Woofer Composition |
woven fiber cone |
Copper-spun IMG |
Woofer Surround Material |
n/a |
Rubber |
Tweeter Size |
25×32 mm" |
1.0" |
Tweeter Type |
folded ribbon |
n/a |
Aimable Tweeter |
No |
No |
Midrange Driver |
5.25" |
No |
Crossover Frequency |
275 Hz and 2700Hz |
n/a |
Firing Direction |
rear |
rear |
Physical Specs |
|
|
Height |
1004.0mm (39.5") |
942.0mm (37.1") |
Width |
213.0mm (8.4") |
239.0mm (9.4") |
Depth |
296.0mm (11.7") |
369.0mm (14.5") |
Weight |
18.20kg (40lbs) |
16.36kg (36lbs) |
Enclosure |
Bass reflex |
Bass Reflex |
Finish |
HDF |
MDF/Wood-grain vinyl |
Available Colors |
Black |
Black |
Grille |
Yes |
Yes |
Moisture Resistancy |
No |
No |
Connections |
|
|
Biamp Inputs |
Yes |
No |
Other |
|
|
Parts Warranty |
5 Years |
5 Years |
Labor Warranty |
5 Years |
5 Years |