In this review, we will be comparing Motion XT B100 and SourcePoint 10, two Passive Bookshelf speakers from MartinLogan and MoFi. Let's have a brief look at the main features
of MartinLogan Motion XT B100 and MoFi SourcePoint 10 first before getting into our more
detailed comparison.
What size room are the MartinLogan Motion XT B100 and MoFi SourcePoint 10 speakers good for?
The size of the room in which you are planning to use these loudspeakers is an important decision factor. Here we have compared their suitability to various sizes of environments considering their size and max power parameters:
In the following sections, we will get into more detail in order to better understand how the MartinLogan Motion XT B100 and MoFi SourcePoint 10 compare and hopefully end up with enough arguments to decide which one of these loudspeakers is the better choice for you.
**This post contains affiliate links, and I will be compensated if you make a purchase after clicking
through my links. As an Amazon Associate I earn from qualifying purchases.
Drivers
Both Motion XT B100 and SourcePoint 10 are 2-way speakers.
| Driver |
MartinLogan Motion XT B100 |
MoFi SourcePoint 10 |
|
Driver Setup
|
2-way
|
2-way
|
|
Tweeter
|
1.25 x 2.4-inch
|
1.25-inch
|
|
Midrange
|
- |
- |
|
Woofer
|
1 x 6.5-inch
|
1 x 10-inch
|
Motion XT B100 features a 1.25 x 2.4" Folded Motion XT Tweeter and 1 x 6.5" Kevlar Woofer with a Crossover frequency at 2600Hz. On the other hand, the SourcePoint 10 features a 1.25" wide roll soft dome Tweeter and 1 x 10" Paper-pulp Woofer with a Crossover frequency at 1600 Hz.
Frequency Response
Motion XT B100 has a frequency range of 45-25k Hz whereas SourcePoint 10 has a frequency range of 42-30k Hz. With a minimum frequency of 42Hz, the SourcePoint 10 can go slightly deeper then the Motion XT B100's min frequency of 45Hz.
Below graphs depict how these two speakers compare with the max, min and average values of the Min and Max Frequencies of other speakers in the Bookshelf class in our database.
Low Frequency
Bookshelf Speakers
High Frequency
Bookshelf Speakers
MartinLogan Motion XT B100
None of these speakers achieves full range experience which is commonly agreed as 20Hz-20kHz. In order to achieve lower lows / deeper bass, we recommend you pair these with a subwoofer. Visit our Powered Subwoofers section to find out more about the available options.
Impedance and Sensitivity
Motion XT B100 is a 4 ohms speaker compared to the SourcePoint 10 which has a nominal impedance of 8 ohms. Lower impedance speakers, especially the ones that are rated at 4 ohms may put more pressure on the amplifier unit especially when played at high volume levels, so make sure the amp you pair with the Motion XT B100 can provide this impedance level.
These two speakers also have different sensitivity levels. Motion XT B100 sensitivity is rated at 93 dB and the SourcePoint 10's is rated at 91dB. This 2 dB difference makes the MartinLogan Motion XT B100 a more sensitive speaker compared to MoFi SourcePoint 10, hence will play louder with the same amount of watts.
Sensitivity
Bookshelf Speakers
Power Range
Power
range is the range of input power in watts RMS that a loudspeaker is designed to handle. While using an amplifier within this range ensures the nominal performance , inputting a power that is higher than the max wattage can result in a damaged speaker.
Motion XT B100 can handle a max power of 250 watts RMS from the amp the whereas SourcePoint 10 has a max power handling value of 200 watts RMS, 50 watts less than the Motion XT B100.
Keep in mind that a higher max power handling value doesn't necessarily make that a louder speaker
compared to a lower max handling speaker. Loudness or the sound level is also impacted by parameters
such as Impedance, sensitivity and system efficiencies.
Input Type and Bi-Amping / Bi-Wiring
Motion XT B100 features Custom 5-way bi-wire tool-less binding posts posts which make bi-amping or bi-wiring possible. SourcePoint 10 has a 5-Way post which doesn't feature bi-amping/bi-wiring.
MartinLogan Motion XT B100's Custom 5-way bi-wire tool-less binding posts terminals allows Bi-amping or bi-wiring
MoFi SourcePoint 10's 5-Way post terminals
Cabinet Type and Port Position
Both Motion XT B100 and SourcePoint 10 have rear firing ports. Rear ported speakers generally need more room between the backside of the speaker and the wall compared to sealed and front/bottom ported speakers. Placing the speakers too close to the walls may cause the bass to sound boomy.
If you are limited in space and can't get the speakers away from the backwall, check our Speakers with Front Firing Ports page.
Physical Specs
Size of a speaker can sometimes become an important decision factor due to space constraints or in some cases purely for esthetic reasons. In this section, we are going to compare MartinLogan Motion XT B100's and MoFi SourcePoint 10's external dimensions. MartinLogan Motion XT B100 has external dimensions of 368 x 203 x 318mm ( 14-1/2-inch x 8inch x 12-1/2inch ) whereas MoFi SourcePoint 10 has external dimensions of 572 x 368 x 406mm ( 22.5 x 14.5 x 16 inch) .
MoFi SourcePoint 10 is clearly the larger of the two speakers. Its body is 165mm wider, 204mm taller and 104mm deeper than MartinLogan Motion XT B100.
Below you can see the front view size comparison of MartinLogan Motion XT B100 and MoFi SourcePoint 10 in scale.
Comparison image of MartinLogan Motion XT B100 and MoFi SourcePoint 10 Size and External Dimensions
Base Surface Area Comparison
Base surface area of a loudspeaker may become a determining factor when the space in your room or desk is limited.
The base surface area of the MartinLogan Motion XT B100 is approximately 645.5cm2 / 100.1inch2 and base area of the MoFi SourcePoint 10 is approximately 1552.0cm2 / 240.6inch2. The Motion XT B100 requires 58% less surface area than the SourcePoint 10 which gives it a small advantage on placement in tight spaces.
Weight Comparison The weight of a loudspeaker can become an important factor if you need to move and reposition the unit often. Weight of a speaker can also "sometimes" be an indicator of the rigidity of the enclosure and the quality of the internal components used. The MartinLogan Motion XT B100 weighs 9.30kg / 20.5lbs and the MoFi SourcePoint 10 weighs 21.00kg / 46.2lbs. This makes the SourcePoint 10 126% heavier than the Motion XT B100.
Here is a comparison of how Motion XT B100 and SourcePoint 10's weights compare with the average, max and min weights in Passive Bookshelf class.
Weight
All Bookshelf Speakers
MartinLogan Motion XT B100
 Max Input Power |
250 watts
vs
200 watts
|
Handle more power from your amplifier |
 Sensitivity |
93 dB
vs
91 dB
|
Play louder with same amount of amplification power |
 Bi-Amping and Bi-Wiring |
Yes
vs
No
|
Allows bi-amping and bi-wiring connections |
 Height |
368mm
vs
572mm
|
Easier to fit in smaller spaces |
 Base Surface Area |
645cm2 (203x318mm)
vs
1552cm2 (368x422mm)
|
Takes less floor space |
 Price per pair* |
1598USD
vs
3699USD
|
costs less (*prices may change depending on the seller, location and time) |
 Nominal Impedance |
8 ohms
vs
4 ohms
|
Less selective with amplifiers |
 Woofer Size |
10 inches
vs
6.5 inches
|
Larger woofer |
| Low Frequency Response |
42 Hz
vs
45 Hz
|
Generates deeper bass |
 High Frequency Response |
30k Hz
vs
25k Hz
|
Generates higher frequency |
| General |
MartinLogan Motion® XT B100 |
MoFi SourcePoint 10 |
| Brand |
MartinLogan |
MoFi |
| Speaker Type |
Bookshelf speakers |
Bookshelf speakers |
| Power Range |
20-250 watts |
30-200 watts |
| Sensitivity |
93 dB |
91dB |
| Impedance |
4 ohms |
8 ohms |
| Impedance |
n/a |
6.2 ohms |
| Frequency Response |
45-25k Hz |
42-30k Hz |
Drivers |
|
|
| Woofer Quantity |
1 |
1 |
| Woofer Size |
6.5" |
10" |
| Woofer Composition |
Kevlar |
Paper-pulp |
| Woofer Surround Material |
Rubber |
n/a |
| Tweeter Size |
1.25 x 2.4" |
1.25" |
| Tweeter Type |
Folded Motion XT |
wide roll soft dome |
| Aimable Tweeter |
No |
No |
| Midrange Driver |
No |
No |
| Crossover Frequency |
2600Hz |
1600 Hz |
| Firing Direction |
rear |
rear |
| Suggested Break-in Period |
Allow 72 hours of break-in |
n/a |
Physical Specs |
|
|
| Height |
368.0mm (14.5") |
572.0mm (22.5") |
| Width |
203.0mm (8") |
368.0mm (14.5") |
| Depth |
318.0mm (12.5") |
422.0mm (16.6") |
| Weight |
9.30kg (20.5lbs) |
21.00kg (46.2lbs) |
| Enclosure |
Bass Reflex |
Bass Reflex |
| Finish |
MDF/Wood veneer |
real wood veneer |
| Available Colors |
Gloss Black, Walnut, and Satin White |
Satin Walnut, Satin Black Ash |
| Mounting Bracket |
No |
No |
| Recommended Stand Height |
24-28" |
n/a |
| Grille |
Yes |
Yes |
| Moisture Resistancy |
No |
No |
Connections |
|
|
| Biamp Inputs |
Yes |
No |
Other |
|
|
| Parts Warranty |
5 Years |
|
| Labor Warranty |
5 Years |
|