In this review, we will be comparing VELA BS 403 and SourcePoint 10, two Passive Bookshelf speakers from ELAC and MoFi. Let's have a brief look at the main features
of ELAC VELA BS 403 and MoFi SourcePoint 10 first before getting into our more
detailed comparison.
What size room are the ELAC VELA BS 403 and MoFi SourcePoint 10 speakers good for?
The size of the room in which you are planning to use these loudspeakers is an important decision factor. Here we have compared their suitability to various sizes of environments considering their size and max power parameters:
In the following sections, we will get into more detail in order to better understand how the ELAC VELA BS 403 and MoFi SourcePoint 10 compare and hopefully end up with enough arguments to decide which one of these loudspeakers is the better choice for you.
**This post contains affiliate links, and I will be compensated if you make a purchase after clicking
through my links. As an Amazon Associate I earn from qualifying purchases.
Drivers
Both VELA BS 403 and SourcePoint 10 are 2-way speakers.
Driver |
ELAC VELA BS 403 |
MoFi SourcePoint 10 |
Driver Setup
|
2-way
|
2-way
|
Tweeter
|
-inch
|
1.25-inch
|
Midrange
|
- |
- |
Woofer
|
1 x 6-inch
|
1 x 10-inch
|
VELA BS 403 features a " handmade JET 5 folded ribbon tweeter Tweeter and 1 x 6" Aluminum/Paper Woofer . On the other hand, the SourcePoint 10 features a 1.25" wide roll soft dome Tweeter and 1 x 10" Paper-pulp Woofer with a Crossover frequency at 1600 Hz.
Frequency Response
VELA BS 403 has a frequency range of 41-50k Hz whereas SourcePoint 10 has a frequency range of 42-30k Hz. With a minimum frequency of 41Hz, the VELA BS 403 can go slightly deeper then the SourcePoint 10's min frequency of 42Hz.
Below graphs depict how these two speakers compare with the max, min and average values of the Min and Max Frequencies of other speakers in the Bookshelf class in our database.
Low Frequency
Bookshelf Speakers
High Frequency
Bookshelf Speakers
None of these speakers achieves full range experience which is commonly agreed as 20Hz-20kHz. In order to achieve lower lows / deeper bass, we recommend you pair these with a subwoofer. Visit our Powered Subwoofers section to find out more about the available options.
Impedance and Sensitivity
VELA BS 403 is a 4 ohms speaker compared to the SourcePoint 10 which has a nominal impedance of 8 ohms. Lower impedance speakers, especially the ones that are rated at 4 ohms may put more pressure on the amplifier unit especially when played at high volume levels, so make sure the amp you pair with the VELA BS 403 can provide this impedance level.
These two speakers also have different sensitivity levels. VELA BS 403 sensitivity is rated at 86 dB and the SourcePoint 10's is rated at 91dB. This 5 dB difference makes the MoFi SourcePoint 10 a more sensitive speaker compared to ELAC VELA BS 403, hence will play louder with the same amount of watts.
Sensitivity
Bookshelf Speakers
Power Range
Power
range is the range of input power in watts RMS that a loudspeaker is designed to handle. While using an amplifier within this range ensures the nominal performance , inputting a power that is higher than the max wattage can result in a damaged speaker.
VELA BS 403 can handle a max power of 200 watts RMS from the amp the whereas VELA BS 403 has a max power handling value of 100 watts RMS , 100 watts less than the SourcePoint 10.
Keep in mind that a higher max power handling value doesn't necessarily make that a louder speaker
compared to a lower max handling speaker. Loudness or the sound level is also impacted by parameters
such as Impedance, sensitivity and system efficiencies.
Input Type and Bi-Amping / Bi-Wiring
VELA BS 403 features Binding post posts which make bi-amping or bi-wiring possible. SourcePoint 10 has a 5-Way post which doesn't feature bi-amping/bi-wiring.
Cabinet Type and Port Position
VELA BS 403 has a bottom firing port whereas SourcePoint 10 has a rear firing ports. ELAC VELA BS 403's bottom-firing port gives more flexibility in placement in regards to proximity to walls compared to MoFi SourcePoint 10 with its rear-firing port.
Physical Specs
Size of a speaker can sometimes become an important decision factor due to space constraints or in some cases purely for esthetic reasons. In this section, we are going to compare ELAC VELA BS 403's and MoFi SourcePoint 10's external dimensions. ELAC VELA BS 403 has external dimensions of 361.0 x 191.0 x 239.0mm ( 24-28inch x 7-1/2inch x 9-3/8inch ) whereas MoFi SourcePoint 10 has external dimensions of 572 x 368 x 406mm ( 22.5 x 14.5 x 16 inch) .
MoFi SourcePoint 10 is clearly the larger of the two speakers. Its body is 177mm wider, 211mm taller and 183mm deeper than ELAC VELA BS 403.
Base Surface Area Comparison
Base surface area of a loudspeaker may become a determining factor when the space in your room or desk is limited.
The base surface area of the ELAC VELA BS 403 is approximately 456.5cm2 / 70.8inch2 and base area of the MoFi SourcePoint 10 is approximately 1552.0cm2 / 240.6inch2. The VELA BS 403 requires 71% less surface area than the SourcePoint 10 which gives it a small advantage on placement in tight spaces.
Weight Comparison The weight of a loudspeaker can become an important factor if you need to move and reposition the unit often. Weight of a speaker can also "sometimes" be an indicator of the rigidity of the enclosure and the quality of the internal components used. The ELAC VELA BS 403 weighs 7.10kg / 15.6lbs and the MoFi SourcePoint 10 weighs 21.00kg / 46.2lbs. This makes the SourcePoint 10 196% heavier than the VELA BS 403.
Here is a comparison of how VELA BS 403 and SourcePoint 10's weights compare with the average, max and min weights in Passive Bookshelf class.
Weight
All Bookshelf Speakers
What's in the Box of ELAC VELA BS 403?
Here are the items that are included inside the box of VELA BS 403:
2 Bookshelf loudspeakers4 Jumper straps (pre-installed)Operating And Safety Instructions
Low Frequency Response |
41 Hz
vs
42 Hz
|
Generates deeper bass |
High Frequency Response |
50k Hz
vs
30k Hz
|
Generates higher frequency |
Bi-Amping and Bi-Wiring |
Yes
vs
No
|
Allows bi-amping and bi-wiring connections |
Height |
361mm
vs
572mm
|
Easier to fit in smaller spaces |
Base Surface Area |
456cm2 (191x239mm)
vs
1552cm2 (368x422mm)
|
Takes less floor space |
Price per pair* |
2899USD
vs
3699USD
|
costs less (*prices may change depending on the seller, location and time) |
Max Input Power |
200 watts
vs
100 watts
|
Handle more power from your amplifier |
Sensitivity |
91 dB
vs
86 dB
|
Play louder with same amount of amplification power |
Nominal Impedance |
8 ohms
vs
4 ohms
|
Less selective with amplifiers |
Woofer Size |
10 inches
vs
6 inches
|
Larger woofer |
General |
ELAC VELA BS 403 |
MoFi SourcePoint 10 |
Brand |
ELAC |
MoFi |
Speaker Type |
Bookshelf speakers |
Bookshelf speakers |
Power Range |
40-100 watts |
30-200 watts |
Sensitivity |
86 dB |
91dB |
Impedance |
4 ohms |
8 ohms |
Impedance |
n/a |
6.2 ohms |
Frequency Response |
41-50k Hz |
42-30k Hz |
Drivers |
|
|
Woofer Quantity |
1 |
1 |
Woofer Size |
6" |
10" |
Woofer Composition |
Aluminum/Paper |
Paper-pulp |
Woofer Surround Material |
Rubber |
n/a |
Tweeter Size |
- |
1.25" |
Tweeter Type |
handmade JET 5 folded ribbon tweeter |
wide roll soft dome |
Aimable Tweeter |
No |
No |
Midrange Driver |
No |
No |
Crossover Frequency |
n/a |
1600 Hz |
Firing Direction |
bottom |
rear |
Physical Specs |
|
|
Height |
361.0mm (14.2") |
572.0mm (22.5") |
Width |
191.0mm (7.5") |
368.0mm (14.5") |
Depth |
239.0mm (9.4") |
422.0mm (16.6") |
Weight |
7.10kg (15.6lbs) |
21.00kg (46.2lbs) |
Enclosure |
Bass Reflex |
Bass Reflex |
Finish |
MDF/Aluminum |
real wood veneer |
Available Colors |
Gloss Black |
Satin Walnut, Satin Black Ash |
Mounting Bracket |
|
No |
Recommended Stand Height |
24-28" |
n/a |
Grille |
No |
Yes |
Moisture Resistancy |
No |
No |
Connections |
|
|
Biamp Inputs |
Yes |
No |
Other |
|
|
Parts Warranty |
3 Years |
|
Labor Warranty |
3 Years |
|